2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B1273 Sliding Roof ECU Communication Stop

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when LIN communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B1273
No communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Sliding roof drive gear sub-assembly
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM

C217632E09

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1273 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the W2 sliding roof drive gear sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - W2-4 (MPX1)
    Always
    Below 1 Ω
    A-16 (LIN2) or W2-4 (MPX1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)

  1. C216964E04
    Disconnect the W2 sliding roof drive gear sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-2 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W2-1 (B) - Body ground
    Always
    11 to 14 V
    W2-5 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
  1. Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1273 is not output.



NG
REPLACE MAIN BODY ECU (Click here)
OK

END (SLIDING ROOF DRIVE GEAR IS DEFECTIVE)


← B1249 Double Locking ECU Communication Stop (from Aug 2014)B1273 Sliding Roof ECU Communication Stop (from Aug 2014) →