B1206 P/W Master Switch Communication Stop
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1206 |
No communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the ignition switch off to troubleshoot:
- HINT:
- When communication between the multiplex network master switch and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B1206 is not output.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH) |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
A-16 (LIN2) - K4-17 (LIN1)
Always
Below 1 Ω
A-16 (LIN2) or K4-17 (LIN1) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
A-16 (LIN2) - J9-17 (LIN1)
Always
Below 1 Ω
A-16 (LIN2) or J9-17 (LIN1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND) |
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
K4-12 (GND) - Body ground
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
J9-12 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
K4-11 (B) - Body ground
Always
11 to 14 V
- for RHD:
Tester Connection
Condition
Specified Condition
J9-11 (B) - Body ground
Always
11 to 14 V
| *A |
for LHD |
| *B |
for RHD |
| *a |
Front view of wire harness connector (to Multiplex Network Master Switch Assembly) |
|
|
||||
| OK | |
| 5. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Temporarily replace the multiplex network master switch assembly with a new or normally functioning one (Click here).
| NEXT | |
| 6. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B1206 is not output.
|
|
||||
| OK | ||
| ||
