2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B1206 P/W Master Switch Communication Stop

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B1206
No communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Multiplex network master switch assembly
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM

C211493E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the multiplex network master switch and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1206 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - K4-17 (LIN1)
    Always
    Below 1 Ω
    A-16 (LIN2) or K4-17 (LIN1) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - J9-17 (LIN1)
    Always
    Below 1 Ω
    A-16 (LIN2) or J9-17 (LIN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)

  1. C216963E02
    Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    K4-12 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    J9-12 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    K4-11 (B) - Body ground
    Always
    11 to 14 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    J9-11 (B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Multiplex Network Master Switch Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
  1. Temporarily replace the multiplex network master switch assembly with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1206 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (MULTIPLEX NETWORK MASTER SWITCH IS DEFECTIVE)


← B1206 P/W Master Switch Communication Stop (Aug 2013 – Jul 2014)B1249 Double Locking ECU Communication Stop (Aug 2013 – Jul 2014) →