2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B1249 Double Locking ECU Communication Stop

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC B1249 is stored when communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.
DTC Code
DTC Detection Condition
Trouble Area
B1249
Communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.
  1. Double lock door control relay assembly
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM

C212385E02

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the double lock door control relay and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1249 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the G49 double lock door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - G49-9 (MPX1)
    Always
    Below 1 Ω
    A-16 (LIN2) or G49-9 (MPX1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - BATTERY AND BODY GROUND)

  1. E179554E07
    Disconnect the G49 double lock door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G49-14 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G49-1 (+B) - Body ground
    Always
    11 to 14 V
    G49-7 (CPUB) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
  1. Temporarily replace the double lock door control relay assembly with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1249 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (DOUBLE LOCK DOOR CONTROL RELAY IS DEFECTIVE)


← B1206 P/W Master Switch Communication Stop (from Aug 2014)B1249 Double Locking ECU Communication Stop (from Aug 2014) →