2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2287 LIN Communication Master Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. DTC B2287 is stored when there is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.
  2. DTC B278C is stored when LIN communication between the certification ECU and power management control ECU stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2287
There is an open or short circuit or an ECU communication malfunction between the power management control ECU and certification ECU.
  1. Certification ECU
  2. Power management control ECU
  3. Harness or connector
B278C
No communication between the certification ECU and power management control ECU for 10 seconds or more.
  1. Certification ECU
  2. Power management control ECU
  3. Harness or connector

WIRING DIAGRAM

C212392E05

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC B2287 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first (Click here).


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2287 or B278C is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the G38 certification ECU connector.

  1. Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G38-29 (LIN) - G51-24 (LIN2)
    Always
    Below 1 Ω
    G38-29 (LIN) or G51-24 (LIN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)

  1. C198951E30
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-5 (GND2) - Body ground
    Always
    Below 1 Ω
    G51-6 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G51-1 (AM22) - Body ground
    Always
    11 to 14 V
    G51-2 (AM21) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Power Management Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE POWER MANAGEMENT CONTROL ECU
  1. Temporarily replace the power management control ECU with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2287 or B278C is not output.



NG
REPLACE CERTIFICATION ECU
OK

END (POWER MANAGEMENT CONTROL ECU IS DEFECTIVE)


← B2287 LIN Communication Master Malfunction (+ B278C) (Aug 2013 – Jul 2014)B2321 Driver Side Door ECU Communication Stop (Aug 2013 – Jul 2014) →