B2321 Driver Side Door ECU Communication Stop
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when LIN communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (main body ECU) stops for 10 seconds or more.- *1: for LHD
- *2: for RHD
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2321 |
No communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (main body ECU) for 10 seconds or more. |
|
- *1: for LHD
- *2: for RHD
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the ignition switch off to troubleshoot:
- HINT:
- When communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
- When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.
- When communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
- *1: for LHD
- *2: for RHD
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2321 is not output.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
K4-16 (LIN2) - K7-9 (LIN)
Always
Below 1 Ω
K4-16 (LIN2) or K7-9 (LIN) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
J9-16 (LIN2) - J7-9 (LIN)
Always
Below 1 Ω
J9-16 (LIN2) or J7-9 (LIN) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND) |
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
K7-1 (GND) - Body ground
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
J7-1 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
K7-2 (B) - Body ground
Always
11 to 14 V
- for RHD:
Tester Connection
Condition
Specified Condition
J7-2 (B) - Body ground
Always
11 to 14 V
| *A |
for LHD |
| *B |
for RHD |
| *a |
Front view of wire harness connector (to Front Power Window Regulator Motor Assembly) |
|
|
||||
| OK | |
| 5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Temporarily replace the front power window regulator motor assembly LH*1 or RH*2 with a new or normally functioning one (Click here).
- *1: for LHD
- *2: for RHD
- *1: for LHD
| NEXT | |
| 6. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2321 is not output.
|
|
||||
| OK | ||
| ||
