2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2785 Communication Malfunction between ECUs Connected by LIN

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.
DTC Code
DTC Detection Condition
Trouble Area
B2785
The certification ECU detects a malfunction in the LIN communication bus between components related to certification continuously 3 times.
  1. Certification ECU
  2. Power management control ECU
  3. ID code box
  4. Steering lock actuator assembly (steering lock ECU)
  5. Harness or connector

WIRING DIAGRAM

C212389E04

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
When DTC B2785 and B2287 are output simultaneously, perform troubleshooting for DTC B2785 first.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2785 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the G38 certification ECU connector.

  1. Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G38-29 (LIN) - G51-24 (LIN2)
    Always
    Below 1 Ω
    G38-29 (LIN) or G51-24 (LIN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CLEAR DTC
  1. Connect the G38 certification ECU connector.

  1. Disconnect the G51 power management control ECU connector.

  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


6. CLEAR DTC
  1. Connect the G51 power management control ECU connector.

  1. Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.

  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output (for Power Tilt and Power Telescopic Steering Column)
    B
    DTC B2785 is not output (for Manual Tilt and Manual Telescopic Steering Column)
    C



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)

C
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
A


8. CLEAR DTC
  1. Connect the G35 steering lock actuator assembly (steering lock ECU) connector.

  1. Disconnect the G37 ID code box connector.

  1. Clear the DTCs (Click here).


NEXT


9. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE ID CODE BOX
A

REPLACE CERTIFICATION ECU


← B2785 Communication Malfunction between ECUs Connected by LIN (Aug 2013 – Jul 2014)B2786 No Response from Steering Lock ECU (Aug 2013 – Jul 2014) →