B2325 LIN Communication Bus Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2 is detected consecutively 3 times.- *1: w/ Double Locking System
- *2: w/ Sliding Roof System
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2325 |
The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors, double lock door control relay assembly*2 and sliding roof drive gear sub-assembly*3 consecutively 3 times. |
|
- *1: for 5 Door
- *2: w/ Double Locking System
- *3: w/ Sliding Roof System
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
- Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- HINT:
- When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC B2325 is not output.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH) |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
A-16 (LIN2) - K4-17 (LIN1)
Always
Below 1 Ω
A-16 (LIN2) or K4-17 (LIN1) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
A-16 (LIN2) - J9-17 (LIN1)
Always
Below 1 Ω
A-16 (LIN2) or J9-17 (LIN1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CLEAR DTC |
- *1: for LHD
- *2: for RHD
Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (Click here).
Reconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 6. CLEAR DTC |
- *1: for LHD
- *2: for RHD
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 8. CLEAR DTC |
- *1: for LHD
- *2: for RHD
Connect the K4*1 or J9*2 multiplex network master switch assembly connector.
Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (for 5 Door)
A
DTC B2325 is output (for 3 Door, w/ Double Locking System)
B
DTC B2325 is output (for 3 Door, w/o Double Locking System, w/ Sliding Roof System)
C
DTC B2325 is output (for 3 Door, w/o Double Locking System, w/o Sliding Roof System)
D
DTC B2325 is not output
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 10. CLEAR DTC |
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the L4 rear power window regulator motor assembly RH connector.
Clear the DTCs (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | |
| 12. CLEAR DTC |
Connect the L4 rear power window regulator motor assembly RH connector.
Disconnect the M4 rear power window regulator motor assembly LH connector.
Clear the DTCs (Click here).
| NEXT | |
| 13. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (w/ Double Locking System)
A
DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System)
B
DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System)
C
DTC B2325 is not output
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 14. CLEAR DTC |
Connect the M4 rear power window regulator motor assembly LH connector.
Disconnect the G49 double lock door control relay assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 15. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (w/ Sliding Roof System)
A
DTC B2325 is output (w/o Sliding Roof System)
B
DTC B2325 is not output
C
|
|
||||
|
|
||||
| A | |
| 16. CLEAR DTC |
w/ Double Locking System:
Connect the G49 double lock door control relay assembly connector.
w/o Double Locking System:
Connect the M4 rear power window regulator motor assembly LH connector.
Disconnect the W2 sliding roof drive gear sub-assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 17. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | ||
| ||
| 18. CLEAR DTC |
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the G49 double lock door control relay assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 19. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output (w/ Sliding Roof System)
A
DTC B2325 is output (w/o Sliding Roof System)
B
DTC B2325 is not output
C
|
|
||||
|
|
||||
| A | |
| 20. CLEAR DTC |
w/ Double Locking System:
Connect the G49 double lock door control relay assembly connector.
w/o Double Locking System:
Connect the K7*1 or J7*2 front power window regulator motor assembly connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the W2 sliding roof drive gear sub-assembly connector.
Clear the DTCs (Click here).
| NEXT | |
| 21. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B2325 is output
A
DTC B2325 is not output
B
|
|
||||
| A | ||
| ||
