2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2325 LIN Communication Bus Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors, double lock door control relay assembly*1 and sliding roof drive gear sub-assembly*2 is detected consecutively 3 times.
  1. *1: w/ Double Locking System
  2. *2: w/ Sliding Roof System
DTC Code
DTC Detection Condition
Trouble Area
B2325
The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors, double lock door control relay assembly*2 and sliding roof drive gear sub-assembly*3 consecutively 3 times.
  1. Multiplex network master switch assembly
  2. Front power window regulator motor assembly LH
  3. Front power window regulator motor assembly RH
  4. Rear power window regulator motor assembly LH*1
  5. Rear power window regulator motor assembly RH*1
  6. Double lock door control relay*2
  7. Sliding roof drive gear sub-assembly*3
  8. Main body ECU (multiplex network body ECU)
  9. Harness or connector
  1. *1: for 5 Door
  2. *2: w/ Double Locking System
  3. *3: w/ Sliding Roof System

WIRING DIAGRAM

C212388E01

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for the LIN communication stop DTC. Then perform troubleshooting for DTC B2325.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2325 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - K4-17 (LIN1)
    Always
    Below 1 Ω
    A-16 (LIN2) or K4-17 (LIN1) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - J9-17 (LIN1)
    Always
    Below 1 Ω
    A-16 (LIN2) or J9-17 (LIN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CLEAR DTC
  1. *1: for LHD
  2. *2: for RHD
  1. Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly (Click here).

  1. Reconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

  1. Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.

  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)
A


6. CLEAR DTC
  1. *1: for LHD
  2. *2: for RHD
  1. Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

  1. Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.

  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)
A


8. CLEAR DTC
  1. *1: for LHD
  2. *2: for RHD
  1. Connect the K4*1 or J9*2 multiplex network master switch assembly connector.

  1. Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.

  1. Clear the DTCs (Click here).


NEXT


9. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output (for 5 Door)
    A
    DTC B2325 is output (for 3 Door, w/ Double Locking System)
    B
    DTC B2325 is output (for 3 Door, w/o Double Locking System, w/ Sliding Roof System)
    C
    DTC B2325 is output (for 3 Door, w/o Double Locking System, w/o Sliding Roof System)
    D
    DTC B2325 is not output
    E



B
Go to step 18

C
Go to step 20

D
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

E
OTHERS FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)
A


10. CLEAR DTC
  1. Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the L4 rear power window regulator motor assembly RH connector.

  1. Clear the DTCs (Click here).


NEXT


11. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A


12. CLEAR DTC
  1. Connect the L4 rear power window regulator motor assembly RH connector.

  1. Disconnect the M4 rear power window regulator motor assembly LH connector.

  1. Clear the DTCs (Click here).


NEXT


13. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output (w/ Double Locking System)
    A
    DTC B2325 is output (w/o Double Locking System, w/ Sliding Roof System)
    B
    DTC B2325 is output (w/o Double Locking System, w/o Sliding Roof System)
    C
    DTC B2325 is not output
    D



B
Go to step 16

C
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

D
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


14. CLEAR DTC
  1. Connect the M4 rear power window regulator motor assembly LH connector.

  1. Disconnect the G49 double lock door control relay assembly connector.

  1. Clear the DTCs (Click here).


NEXT


15. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output (w/ Sliding Roof System)
    A
    DTC B2325 is output (w/o Sliding Roof System)
    B
    DTC B2325 is not output
    C



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (Click here)
A


16. CLEAR DTC
  1. w/ Double Locking System:

    1. Connect the G49 double lock door control relay assembly connector.

  1. w/o Double Locking System:

    1. Connect the M4 rear power window regulator motor assembly LH connector.

  1. Disconnect the W2 sliding roof drive gear sub-assembly connector.

  1. Clear the DTCs (Click here).


NEXT


17. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

18. CLEAR DTC
  1. Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the G49 double lock door control relay assembly connector.

  1. Clear the DTCs (Click here).


NEXT


19. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output (w/ Sliding Roof System)
    A
    DTC B2325 is output (w/o Sliding Roof System)
    B
    DTC B2325 is not output
    C



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (Click here)
A


20. CLEAR DTC
  1. w/ Double Locking System:

    1. Connect the G49 double lock door control relay assembly connector.

  1. w/o Double Locking System:

    1. Connect the K7*1 or J7*2 front power window regulator motor assembly connector.

      1. *1: for LHD
      2. *2: for RHD

  1. Disconnect the W2 sliding roof drive gear sub-assembly connector.

  1. Clear the DTCs (Click here).


NEXT


21. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← B2324 Rear Door LH ECU Communication Stop (from Aug 2014)B2325 LIN Communication Bus Malfunction (from Aug 2014) →