Speed Signal Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The vehicle speed signal consists of pulses sent to the combination meter assembly from the master cylinder solenoid or brake actuator assembly (skid control ECU).WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE) |
Disconnect the G6 meter connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G6-32 (+S) - Body ground
Ignition switch ON
4.5 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
|
|
||||
| OK | |
| 2. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) |
for 1GR-FE, 1KD-FTV:
Disconnect the A7 master cylinder solenoid (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A7-12 (SP1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))
for 2TR-FE, 5L-E:
Disconnect the A6 brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A6-11 (SP1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU))
|
|
||||
| OK | |
| 3. CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL) |
Check the input waveform.

Reconnect the G6 meter connector.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal G6-33 (SI) and body ground.
Turn the ignition switch to ON.
Check the signal waveform according to the condition(s) in the table below.
Measurement Condition Item
Condition
Terminal No. (Symbol)
G6-33 (SI) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Condition
Driving at approximately 20 km/h (12 mph)
- OK:
- The waveform displayed is as shown in the illustration.
- HINT:
- When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
Result Result
Proceed to
OK
A
NG (for LHD, w/ Hydraulic Brake Booster)
B
NG (for RHD, w/ Hydraulic Brake Booster)
C
NG (w/ Vacuum Brake Booster)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU) |
for 1GR-FE, 1KD-FTV:
Disconnect the G6 meter connector.
Disconnect the A7 master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G6-33 (SI) - A7-12 (SP1)
Always
Below 1 Ω
A7-12 (SP1) - Body ground
Always
10 kΩ or higher
for 2TR-FE, 5L-E:
Disconnect the G6 meter connector.
Disconnect the A6 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G6-33 (SI) - A6-11 (SP1)
Always
Below 1 Ω
A6-11 (SP1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK) |
Disconnect the G6 meter connector.
Disconnect the 3A junction block connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G6-32 (+S) - 3A-59
Always
Below 1 Ω
G6-32 (+S) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK) |
Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.
- HINT:
- If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.
Disconnect the 3B junction block connector.


Text in Illustration *1
No. 3 Junction Block
-
-
*a
Front view of wire harness connector
(to No. 3 Junction Block)
-
-
Disconnect the 3C junction block connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
3C-24 - Body ground*1
Ignition switch ON
4.5 to 14 V
3B-72 - Body ground*2
Ignition switch ON
4.5 to 14 V
3A-22 - Body ground*3
Ignition switch ON
4.5 to 14 V
3A-60 - Body ground
Ignition switch ON
4.5 to 14 V
3A-35 - Body ground*4
Ignition switch ON
4.5 to 14 V
- *1: w/ Auto Wiper System
- *2: w/ Entry and Start System
- *3: w/ Audio and Visual System or Navigation System
- *4: w/ Tire Pressure Monitor System
Result Result
Proceed to
Voltage is not as specified in one circuit
A
Voltage is as specified in all circuits
B
|
|
||||
| A | |
| 7. SYSTEM CHECK |
Select the circuit for which voltage was not as specified in the previous step.
Result Tester Connection
System that Uses the Circuit
Proceed to
3C-24 - Body ground
Auto wiper system*1
A
3B-72 - Body ground
Entry and start system*2
B
3A-22 - Body ground
Audio and visual system*3 or navigation system*4
C
3A-60 - Body ground
SFI system, TOYOTA parking assist-sensor system*5, automatic transmission system*6*7
D
3A-35 - Body ground
Tire pressure monitor system*8
E
- *1: w/ Auto Wiper System
- *2: w/ Entry and Start System
- *3: w/o Navigation System
- *4: w/ Navigation System
- *5: w/ TOYOTA Parking Assist-sensor System
- *6: for 1KD-FTV
- *7: for Automatic Transmission
- *8: w/ Tire Pressure Monitor System
- *1: w/ Auto Wiper System
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 8. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - WINDSHIELD WIPER SWITCH ASSEMBLY) |
Disconnect the G120 auto wiper switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G120-6 (SPD) - Body ground*1
Always
10 kΩ or higher
G120-4 (SPD) - Body ground*2, *3
Always
10 kΩ or higher
- *1: for LHD
- *2: for RHD
- *3: for Headlight Dimmer Switch Assembly RH Side Type
|
|
||||
| OK | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-23 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - JUNCTION CONNECTOR) |
Disconnect the 3A junction block connector.
Disconnect the H24 junction connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3A-22 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR) |
Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.
Disconnect the H25 junction block connector.

Text in Illustration *a
Front view of wire harness connector
(Junction Connector)
Measure the voltage according to the value(s) in the table below
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
H25-10 - Body ground*1
Ignition switch ON
4.5 to 14 V
H25-11 - Body ground*2
Ignition switch ON
4.5 to 14 V
- *1: w/ Radio Receiver Assembly or Navigation System
- *2: w/ Stereo Component Amplifier
Result Result
Proceed to
NG (H25-10 - Body ground)
A
NG (H25-11 - Body ground)
B
OK
C
|
|
||||
|
|
||||
| A | |
| 12. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
- NOTICE:
- For vehicles with a navigation system, go to "Check Navigation Receiver Assembly".
Disconnect the H51 radio and display receiver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H51-17 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 13. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the H56 navigation receiver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H56-17 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 14. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the H63 stereo component amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H63-11 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 15. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - NO. 4 JUNCTION BLOCK) |
Disconnect the 3A junction block connector.
Disconnect the 4A junction block connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3A-60 (+S) - 4A-48
Always
Below 1 Ω
3A-60 (+S) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 16. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK) |
Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.
Disconnect the 4A junction block connector.
Disconnect the 4B junction block connector.


Text in Illustration *1
No. 4 Junction Block
-
-
*a
Front view of wire harness connector
(to No. 4 Junction Block)
-
-
Measure the voltage according to the value(s) in the table below
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
4B-49 - Body ground*1
Ignition switch ON
4.5 to 14 V
4B-1 - Body ground*2, *3
Ignition switch ON
4.5 to 14 V
4A-96 - Body ground
Ignition switch ON
4.5 to 14 V
- *1: TOYOTA Parking Assist-sensor System
- *2: for 1KD-FTV
- *3: for Automatic Transmission
Result Result
Proceed to
NG (4B-49 - Body ground)
A
NG (4B-1 - Body ground)
B
NG (4A-96 - Body ground)
C
OK
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 17. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - CLEARANCE WARNING ECU) |
Disconnect the I1 clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I1-10 (SPD) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 18. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - TCM) |
Disconnect the G70 TCM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G70-25 (SPD1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 19. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - ECM) |
for 1GR-FE:Disconnect the G55 ECM connector.
for 2TR-FE:Disconnect the G60 ECM connector.
for 1KD-FTV:Disconnect the G58 ECM connector.
for 5L-E:Disconnect the G61 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1GR-FE Tester Connection
Condition
Specified Condition
G55-18 (SPD) - Body ground
Always
10 kΩ or higher
G55-18 (SPD) - 4A-96
Always
Below 1 Ω
for 2TR-FE Tester Connection
Condition
Specified Condition
G60-16 (SPD) - Body ground
Always
10 kΩ or higher
G60-16 (SPD) - 4A-96
Always
Below 1 Ω
for 1KD-FTV Tester Connection
Condition
Specified Condition
G58-30 (SPD) - Body ground
Always
10 kΩ or higher
G58-30 (SPD) - 4A-96
Always
Below 1 Ω
for 5L-E Tester Connection
Condition
Specified Condition
G61-9 (SPD) - Body ground
Always
10 kΩ or higher
G61-9 - 4A-96
Always
Below 1 Ω
Result Result
Proceed to
NG
A
OK (for 1GR-FE)
B
OK (for 2TR-FE)
C
OK (for 1KD-FTV)
D
OK (for 5L-E)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 20. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY) |
Disconnect the R41 tire pressure monitor receiver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R41-2 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
