2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Speed Signal Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the master cylinder solenoid or brake actuator assembly (skid control ECU).

WIRING DIAGRAM

E197886E05
E283909E01

INSPECTION PROCEDURE


1. CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)

  1. E179098E15
    Disconnect the G6 meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-32 (+S) - Body ground
    Ignition switch ON
    4.5 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 5
OK


2. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

  1. for 1GR-FE, 1KD-FTV:

    1. Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

    2. E202163E01
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A7-12 (SP1) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Master Cylinder Solenoid (Skid Control ECU))

  1. for 2TR-FE, 5L-E:

    1. Disconnect the A6 brake actuator assembly (skid control ECU) connector.

    2. E202162E01
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A6-11 (SP1) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Brake Actuator Assembly (Skid Control ECU))



NG
Go to step 4
OK


3. CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

  1. E200403E02
    Check the input waveform.
    1. Reconnect the G6 meter connector.

    2. Remove the combination meter assembly with the connector(s) still connected.

    3. Connect an oscilloscope to terminal G6-33 (SI) and body ground.

    4. Turn the ignition switch to ON.

    5. Check the signal waveform according to the condition(s) in the table below.

      Measurement Condition 
      Item
      Condition
      Terminal No. (Symbol)
      G6-33 (SI) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Driving at approximately 20 km/h (12 mph)

      OK:
      The waveform displayed is as shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.

      Result 
      Result
      Proceed to
      OK
      A
      NG (for LHD, w/ Hydraulic Brake Booster)
      B
      NG (for RHD, w/ Hydraulic Brake Booster)
      C
      NG (w/ Vacuum Brake Booster)
      D



B
REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)(for LHD) (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)(for RHD) (Click here)

D
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
  1. for 1GR-FE, 1KD-FTV:

    1. Disconnect the G6 meter connector.

    2. Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G6-33 (SI) - A7-12 (SP1)
      Always
      Below 1 Ω
      A7-12 (SP1) - Body ground
      Always
      10 kΩ or higher

  1. for 2TR-FE, 5L-E:

    1. Disconnect the G6 meter connector.

    2. Disconnect the A6 brake actuator assembly (skid control ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G6-33 (SI) - A6-11 (SP1)
      Always
      Below 1 Ω
      A6-11 (SP1) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK)
  1. Disconnect the G6 meter connector.

  1. Disconnect the 3A junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-32 (+S) - 3A-59
    Always
    Below 1 Ω
    G6-32 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK)

  1. Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

    HINT:
    If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.

    1. Disconnect the 3B junction block connector.E200511E06

      Text in Illustration 
      *1
      No. 3 Junction Block
      -
      -
      *a
      Front view of wire harness connector
      (to No. 3 Junction Block)
      -
      -

    2. Disconnect the 3C junction block connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      3C-24 - Body ground*1
      Ignition switch ON
      4.5 to 14 V
      3B-72 - Body ground*2
      Ignition switch ON
      4.5 to 14 V
      3A-22 - Body ground*3
      Ignition switch ON
      4.5 to 14 V
      3A-60 - Body ground
      Ignition switch ON
      4.5 to 14 V
      3A-35 - Body ground*4
      Ignition switch ON
      4.5 to 14 V

      1. *1: w/ Auto Wiper System
      2. *2: w/ Entry and Start System
      3. *3: w/ Audio and Visual System or Navigation System
      4. *4: w/ Tire Pressure Monitor System
      Result 
      Result
      Proceed to
      Voltage is not as specified in one circuit
      A
      Voltage is as specified in all circuits
      B



B
REPLACE NO. 3 JUNCTION BLOCK
A


7. SYSTEM CHECK
  1. Select the circuit for which voltage was not as specified in the previous step.

    Result 
    Tester Connection
    System that Uses the Circuit
    Proceed to
    3C-24 - Body ground
    Auto wiper system*1
    A
    3B-72 - Body ground
    Entry and start system*2
    B
    3A-22 - Body ground
    Audio and visual system*3 or navigation system*4
    C
    3A-60 - Body ground
    SFI system, TOYOTA parking assist-sensor system*5, automatic transmission system*6*7
    D
    3A-35 - Body ground
    Tire pressure monitor system*8
    E
    1. *1: w/ Auto Wiper System
    2. *2: w/ Entry and Start System
    3. *3: w/o Navigation System
    4. *4: w/ Navigation System
    5. *5: w/ TOYOTA Parking Assist-sensor System
    6. *6: for 1KD-FTV
    7. *7: for Automatic Transmission
    8. *8: w/ Tire Pressure Monitor System



B
Go to step 9

C
Go to step 10

D
Go to step 15

E
Go to step 20
A


8. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - WINDSHIELD WIPER SWITCH ASSEMBLY)
  1. Disconnect the G120 auto wiper switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G120-6 (SPD) - Body ground*1
    Always
    10 kΩ or higher
    G120-4 (SPD) - Body ground*2, *3
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD
    3. *3: for Headlight Dimmer Switch Assembly RH Side Type



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)

9. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-23 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

10. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - JUNCTION CONNECTOR)
  1. Disconnect the 3A junction block connector.

  1. Disconnect the H24 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-22 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

  1. Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

    1. E202282E02
      Disconnect the H25 junction block connector.
      Text in Illustration 
      *a
      Front view of wire harness connector
      (Junction Connector)

    2. Measure the voltage according to the value(s) in the table below

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      H25-10 - Body ground*1
      Ignition switch ON
      4.5 to 14 V
      H25-11 - Body ground*2
      Ignition switch ON
      4.5 to 14 V

      1. *1: w/ Radio Receiver Assembly or Navigation System
      2. *2: w/ Stereo Component Amplifier
      Result 
      Result
      Proceed to
      NG (H25-10 - Body ground)
      A
      NG (H25-11 - Body ground)
      B
      OK
      C



B
Go to step 14

C
REPLACE JUNCTION CONNECTOR
A


12. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles with a navigation system, go to "Check Navigation Receiver Assembly".

  1. Disconnect the H51 radio and display receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H51-17 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

13. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the H56 navigation receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H56-17 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

14. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. Disconnect the H63 stereo component amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H63-11 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

15. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - NO. 4 JUNCTION BLOCK)
  1. Disconnect the 3A junction block connector.

  1. Disconnect the 4A junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-60 (+S) - 4A-48
    Always
    Below 1 Ω
    3A-60 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK)

  1. Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

    1. Disconnect the 4A junction block connector.

    2. Disconnect the 4B junction block connector.E200515E02

      Text in Illustration 
      *1
      No. 4 Junction Block
      -
      -
      *a
      Front view of wire harness connector
      (to No. 4 Junction Block)
      -
      -

    3. Measure the voltage according to the value(s) in the table below

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      4B-49 - Body ground*1
      Ignition switch ON
      4.5 to 14 V
      4B-1 - Body ground*2, *3
      Ignition switch ON
      4.5 to 14 V
      4A-96 - Body ground
      Ignition switch ON
      4.5 to 14 V

      1. *1: TOYOTA Parking Assist-sensor System
      2. *2: for 1KD-FTV
      3. *3: for Automatic Transmission
      Result 
      Result
      Proceed to
      NG (4B-49 - Body ground)
      A
      NG (4B-1 - Body ground)
      B
      NG (4A-96 - Body ground)
      C
      OK
      D



B
Go to step 18

C
Go to step 19

D
REPLACE NO. 4 JUNCTION BLOCK
A


17. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - CLEARANCE WARNING ECU)
  1. Disconnect the I1 clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-10 (SPD) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE CLEARANCE WARNING ECU ASSEMBLY (for LHD) (Click here)

C
REPLACE CLEARANCE WARNING ECU ASSEMBLY (for RHD) (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

18. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - TCM)
  1. Disconnect the G70 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G70-25 (SPD1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)

19. CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - ECM)
  1. for 1GR-FE:Disconnect the G55 ECM connector.

  1. for 2TR-FE:Disconnect the G60 ECM connector.

  1. for 1KD-FTV:Disconnect the G58 ECM connector.

  1. for 5L-E:Disconnect the G61 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G55-18 (SPD) - Body ground
    Always
    10 kΩ or higher
    G55-18 (SPD) - 4A-96
    Always
    Below 1 Ω
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G60-16 (SPD) - Body ground
    Always
    10 kΩ or higher
    G60-16 (SPD) - 4A-96
    Always
    Below 1 Ω
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G58-30 (SPD) - Body ground
    Always
    10 kΩ or higher
    G58-30 (SPD) - 4A-96
    Always
    Below 1 Ω
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G61-9 (SPD) - Body ground
    Always
    10 kΩ or higher
    G61-9 - 4A-96
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1GR-FE)
    B
    OK (for 2TR-FE)
    C
    OK (for 1KD-FTV)
    D
    OK (for 5L-E)
    E



B
REPLACE ECM (for 1GR-FE) (Click here)

C
REPLACE ECM (for 2TR-FE) (Click here)

D
REPLACE ECM (for 1KD-FTV) (Click here)

E
REPLACE ECM (for 5L-E) (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

20. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY)
  1. Disconnect the R41 tire pressure monitor receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R41-2 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY (Click here)


← Meter Illumination does not Dim at Night (from Aug 2014)Speed Signal Circuit (from Aug 2014) →