2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Injector Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

Refer to DTC P0201 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).


1. CHECK INJECTOR DRIVER (POWER SOURCE)

  1. A204910E14
    Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C121-2 (+B) - C121-4 (GND)
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver)

  1. Reconnect the injector driver connectors.



NG
Go to step 2
OK

REPLACE INJECTOR DRIVER (Click here)

2. INSPECT EDU RELAY
  1. Inspect the EDU relay (Click here).



NG
REPLACE EDU RELAY
OK


3. CHECK HARNESS AND CONNECTOR (EDU RELAY - INJECTOR DRIVER)
  1. Remove the EDU relay from the engine room relay block.

  1. Disconnect the injector driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C121-2 (+B) - EDU relay terminal 3
    Always
    Below 1 Ω
    C121-4 (GND) - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C121-2 (+B) or EDU relay terminal 3 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reinstall the EDU relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (EDU RELAY - NO. 1 INTEGRATION RELAY, BATTERY)
  1. Remove the EDU relay from the engine room relay block.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    EDU relay terminal 1 - 1B-5
    Always
    Below 1 Ω
    EDU relay terminal 5 - positive (+) battery terminal
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    EDU relay terminal 1 or 1B-5 - Body ground
    Always
    10 kΩ or higher
    EDU relay terminal 5 or positive (+) battery terminal - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the EDU relay.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT NO. 1 INTEGRATION RELAY (EFI)
  1. Inspect the No. 1 integration relay (EFI) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


6. CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)
  1. Remove the EDU relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G58-12 (IREL) - EDU relay terminal 2
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G58-12 (IREL) or EDU relay terminal 2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the EDU relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Injector Circuit (Aug 2013 – Jul 2014)Brake Override System (Aug 2013 – Jul 2014) →