2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for 6 seconds or more.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM

WIRING DIAGRAM

B235867E23

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly and/or ECM, refer to the Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If any DTCs other than B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
  1. Disconnect the G74 ECU connector.

  1. Disconnect the G60*1, G56*2 or G58*3 ECM connector.

    1. *1: for 2TR-FE
    2. *2: for 1GR-FE
    3. *3: for 1KD-FTV

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G60-31 (IMI)
    Always
    Below 1 Ω
    G74-13 (EFIO) or G60-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G56-14 (IMI)
    Always
    Below 1 Ω
    G74-13 (EFIO) or G56-14 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - G58-28 (IMI)
    Always
    Below 1 Ω
    G74-13 (EFIO) or G58-28 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - Body ground
    Always
    Below 1 V
    G60-31 (IMI) - Body ground
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - Body ground
    Always
    Below 1 V
    G56-14 (IMI) - Body ground
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G74-13 (EFIO) - Body ground
    Always
    Below 1 V
    G58-28 (IMI) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

  1. Using an oscilloscope, check the waveform.B242189E07

    Text in Illustration 
    *A
    for 2TR-FE
    *B
    for 1GR-FE
    *C
    for 1KD-FTV
    -
    -
    *a
    Component with harness connected
    (ECM)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    G60-31 (IMI) - Body ground*1
    G56-14 (IMI) - Body ground*2
    G58-28 (IMI) - Body ground*3
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON
    1. *1: for 2TR-FE
    2. *2: for 1GR-FE
    3. *3: for 1KD-FTV

    OK:
    Waveform is output normally (refer to illustration).



NG
Go to step 5
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)

  1. B242622E13
    Disconnect the G74 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G74-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G74-16 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly (Refer to the Service Bulletin).


NEXT


7. REGISTER ECU - ECM COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


8. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B279A is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2TR-FE)
    B
    NG (for 1GR-FE)
    C
    NG (for 1KD-FTV)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU IS DEFECTIVE)


← B279A Theft Deterrent System Communication Line High Fixation (Aug 2013 – Jul 2014)B279C Theft Deterrent System Presence Detection (Aug 2013 – Jul 2014) →