2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

OPERATION CHECK

Troubleshooting · Vehicles built from Aug 2013


INSPECT INDICATOR/WARNING LIGHT
  1. Check the following indicators and warning lights.

    Indicator/Warning Light
    Switch Condition
    Specified Condition
    BRAKE warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    ABS warning light
    SLIP indicator light*1
    TRC OFF indicator light*1
    VSC OFF indicator light*1
    CRAWL indicator light*3
    Downhill assist control indicator light*4
    KDSS indicator light*5
    Eco driving indicator Light*6
    Oil Maintenance warning indicator light*2, *7, *8
    OIL LEVEL indicator light*8, *9
    T-BELT indicator light*2, *8, *10
    FUEL FILTER & SEDIMENTER indicator light*2, *8, *11
    SEDIMENTER indicator light*2, *9, *10
    SPEED LIMIT indicator light*12
    PCS indicator light*13
    PPS warning light*1
    Master warning light*15
    BSM indicator light*17
    Headlight beam level control system warning light*14
    LED headlight warning light*14
    Tire pressure warning light*18
    SRS warning light
    Ignition switch off → ON
    Comes on for 6 seconds
    CHARGE warning light
    Ignition switch off → ON
    1. Illuminates when ignition switch turned to ON
    2. Turns off when engine started
    OIL PRESSURE warning light
    A/T TEMP warning light*6
    MIL
    SIL indicator light*7, *8, *16
    1. *1: except 5L-E
    2. *2: for Analog Meter
    3. *3: w/ Crawl Control
    4. *4: w/ Downhill Assist Control
    5. *5: w/ Kinetic Dynamic Suspension System
    6. *6: for Automatic Transmission
    7. *7: for Europe
    8. *8: for 1KD-FTV
    9. *9: for Europe 1KD-FTV
    10. *10: for 5L-E
    11. *11: except Europe
    12. *12: for Middle East
    13. *13: w/ Pre-crash Safety System
    14. *14: for LED Headlight
    15. *15: for Optitron Meter
    16. *16: for Manual Transmission
    17. *17: w/ Blind Spot Monitor System
    18. *18: w/ Tire Pressure Monitor System


INSPECT SPEEDOMETER
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Data List.

    Reference:
    for mph 
    Standard Indication
    Acceptable Range
    40 mph
    42 to 44.5 mph
    80 mph
    83.1 to 87.1 mph
    120 mph
    124.7 to 129.6 mph
    for km/h (except Australia) 
    Standard Indication
    Acceptable Range
    40 km/h
    41.7 to 46.2 km/h
    80 km/h
    83.4 to 88.4 km/h
    120 km/h
    125.1 to 130.6 km/h
    160 km/h
    166.2 to 173.2 km/h
    200 km/h
    207.7 to 215.7 km/h
    for Australia 
    Standard Indication
    Acceptable Range
    20 km/h
    20.7 to 24.7 km/h
    40 km/h
    41.4 to 45.9 km/h
    60 km/h
    62.1 to 66.6 km/h
    80 km/h
    82.8 to 87.8 km/h
    100 km/h
    103.5 to 107.5 km/h
    120 km/h
    124.2 to 129.2 km/h
    140 km/h
    144.9 to 149.9 km/h
    160 km/h
    165.6 to 170.6 km/h
    180 km/h
    186.3 to 191.3 km/h

    If the result is not as specified, the speedometer may have a malfunction.

    NOTICE:
    Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

  5. Check the deflection width of the speedometer indicator.

    Reference:
    Within 0.3°


INSPECT TACHOMETER
  1. Connect a tune-up tachometer and start the engine.

  2. Compare the test results with the tachometer indicator.

    DC 13.5 V at 25°C (77°F):
    Standard Indication
    Acceptable Range
    Data in ( ) is for Reference
    700 rpm
    630 to 770 rpm
    1000 rpm
    (900 to 1100) rpm
    2000 rpm
    (1850 to 2150) rpm
    3000 rpm
    2800 to 3200 rpm
    4000 rpm
    (3800 to 4200) rpm
    5000 rpm
    4800 to 5200 rpm
    6000 rpm
    (5750 to 6250) rpm
    7000 rpm
    6700 to 7300 rpm
    8000 rpm
    7700 to 8300 rpm

    If the result is not as specified, the tachometer may have a malfunction.


INSPECT METER/GAUGE
  1. Connect the intelligent tester to the DLC3.

  2. Perform the Active Test (Click here).

    OK:
    Each meter/gauge needle indication is normal.


INSPECT WARNING/INDICATOR LIGHT
  1. Connect the intelligent tester to the DLC3.

  2. Perform the Active Test (Click here).

    OK:
    Each warning/indicator light can be turned on and off using the intelligent tester.


INSPECT MULTI-INFORMATION DISPLAY (for Analog Meter)
  1. Connect the intelligent tester to the DLC3.

  2. Perform the Active Test (Click here).

    HINT:
    If this Active Test is being performed and the ignition switch is turned off and then to ON, the clock and ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.

    OK:
    All segments in the multi-information display can be turned on and off using the intelligent tester.


INSPECT MULTI-INFORMATION DISPLAY (for Optitron Meter)
  1. Connect the intelligent tester to the DLC3.

  2. Perform the Active Test (Click here).

    HINT:
    If this Active Test is being performed and the ignition switch is turned off and then to ON, the ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.

    OK:
    All dots in the multi-information display can be turned on and off using the intelligent tester.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2014)CUSTOMIZE PARAMETERS (from Aug 2013) →