2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Operating Light Control Rheostat does not Change Light Brightness

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the light control rheostat knob is turned right, the combination meter and vehicle interior illumination will become brighter. When the light control rheostat knob is turned left, the combination meter and vehicle illumination will dim.

WIRING DIAGRAM

E202081E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (LIGHT CONTROL RHEOSTAT)
  1. Operate the intelligent tester according to the display and select Data List (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tail Cancel SW*
    TAIL cancel switch condition/ON or OFF
    ON: TAIL cancel switch ON
    OFF: TAIL cancel switch OFF
    -
    Rheostat value
    Light control rheostat switch input/Min.: 0, Max.: 100
    Light control rheostat switch is fully turned left (0) → fully turned right (100)
    Unit: %
    1. *: w/ TAIL Cancel Switch

    OK:
    Light brightness can be changed within specified range by manual operation.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

2. INSPECT LIGHT CONTROL RHEOSTAT

  1. Inspect the light control rheostat. (w/o TAIL Cancel Switch)E195766E01

    1. Remove the light control rheostat (Click here).

    2. Measure the resistance according to the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Switch Condition
      Specified Condition
      5 (T) - 1 (E)
      Always
      8 to 12 kΩ
      7 (RV) - 1 (E)
      Light control rheostat fully turned right → fully turned left
      Below 100 Ω → 8 to 12 kΩ
      for RHD 
      Tester Connection
      Switch Condition
      Specified Condition
      8 (T) - 4 (E)
      Always
      8 to 12 kΩ
      6 (RV) - 4 (E)
      Light control rheostat fully turned right → fully turned left
      Below 100 Ω → 8 to 12 kΩ

  1. Inspect the light control rheostat. (w/ TAIL Cancel Switch)E195765E01

    1. Remove the light control rheostat (Click here).

    2. Measure the resistance according to the table below.

      Standard Resistance:
      for LHD 
      Tester Connection
      Switch Condition
      Specified Condition
      5 (T) - 6 (TC)
      TAIL cancel switch off → on
      1 MΩ or higher → Below 1 Ω
      5 (T) - 1 (E)
      Always
      8 to 12 kΩ
      7 (RV) - 1 (E)
      Light control rheostat fully turned right → fully turned left
      Below 100 Ω → 8 to 12 kΩ
      for RHD 
      Tester Connection
      Switch Condition
      Specified Condition
      8 (T) - 7 (TC)
      TAIL cancel switch off → on
      1 MΩ or higher → Below 1 Ω
      8 (T) - 4 (E)
      Always
      8 to 12 kΩ
      6 (RV) - 4 (E)
      Light control rheostat fully turned right → fully turned left
      Below 100 Ω → 8 to 12 kΩ



NG
REPLACE LIGHT CONTROL RHEOSTAT (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT)
  1. Disconnect the G6 meter connector.

  1. Disconnect the G16 rheostat connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    G6-10 (TC) - G16-6 (TC)*
    Always
    Below 1 Ω
    G6-6 (SW1) - G16-5 (T)
    G6-7 (SW2) - G16-7 (RV)
    G6-22 (SW3) - G16-1 (E)
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    G6-10 (TC) - G16-7 (TC)*
    Always
    Below 1 Ω
    G6-6 (SW1) - G16-8 (T)
    G6-7 (SW2) - G16-6 (RV)
    G6-22 (SW3) - G16-4 (E)

    1. *: w/ TAIL Cancel Switch



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or normally operating one. Perform an operation inspection.

    OK:
    Combination meter assembly operates normally.



NG
GO TO LIGHTING SYSTEM (Click here)
OK

END


← Odo/Trip Switch Malfunction (from Aug 2014)Operating Light Control Rheostat does not Change Light Brightness (from Aug 2014) →