2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK NAVIGATION RECEIVER ASSEMBLY
C294486E03
  1. Disconnect the H60 and H61 navigation receiver assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    H60-3 (ACC1) - H60-7 (GND1)
    GR - BR
    Power source (ACC)
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    11 to 14 V
    H60-4 (+B1) - H60-7 (GND1)
    R - BR
    Power source (+B)
    Always
    11 to 14 V
    H60-7 (GND1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    H61-1 (IG) - H60-7 (GND1)
    L - BR
    Power source (IG)
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V

  3. Reconnect the H60 and H61 navigation receiver assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    H61-2 (REV) - H60-7 (GND1)
    R - BR
    Reverse signal
    Engine switch on (IG), shift lever in R
    7.5 to 14 V
    Engine switch on (IG), shift lever not in R
    Below 1 V
    H62-7 (CA+) - H62-15 (CGND)
    B - Shielded
    Power source
    Engine switch on (IG) (ACC)
    5.5 to 7.05 V
    H62-8 (V+) - H62-15 (CGND)
    R - Shielded
    Display signal
    Engine switch on (IG)
    Pulse generation (See waveform 1)
    Engine switch on (IG), screen blacked out by covering camera lens
    Pulse generation (See waveform 2)
    H62-15 (CGND) - Body ground
    Shielded - Body ground
    Shielded ground
    Always
    Below 1 V

  5. E171712E24
    Using an oscilloscope, check the waveform.

    1. Waveform 1

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      H62-8 (V+) - H62-15 (CGND)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Engine switch on (IG)

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      H62-8 (V+) - H62-15 (CGND)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Engine switch on (IG), screen blacked out by covering camera lens

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronized Signal
      *d
      Video Waveform


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →