2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


PARKING ASSIST ECU
E245334E21
  1. Disconnect the I6 and I7 parking assist ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I6-1 (+B) - I6-4 (GND1)
    L - W-B
    Power source signal
    Always
    10 to 16 V
    I6-4 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I6-8 (IG) - I6-4 (GND1)
    L - W-B
    IG power source signal
    Engine switch on (IG)
    10 to 16 V
    Engine switch off
    Below 1 V
    I6-9 (ACC) - I6-4 (GND1)
    P - W-B
    ACC power source signal
    Engine switch on (ACC)
    10 to 16 V
    Engine switch off
    Below 1 V
    I7-8 (BLSW) - I6-4 (GND1)
    L - W-B
    Front and side monitor main switch power source signal
    Engine switch on (IG), front and side monitor main switch on
    10 to 16 V

  3. Reconnect the I6 and I7 parking assist ECU connectors.

  4. Measure the voltage, resistance and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I6-10 (TX-)
    LG
    AVC-LAN communication signal
    -
    -
    I6-11 (TX+)
    L
    AVC-LAN communication signal
    -
    -
    I7-15 (CV+) - I7-37 (CGND)
    R - GR
    Rear television camera display signal input
    Engine switch on (IG), camera lens not covered, displaying image
    Pulse generation (See waveform 1)
    Engine switch on (IG), camera lens covered, blacking out screen
    Pulse generation (See waveform 2)
    I7-14 (CB+) - I7-37 (CGND)
    B - GR
    Power source to rear television camera
    Engine switch on (IG)
    5.5 to 7.05 V
    I7-27 (REV) - I6-4 (GND1)
    R - W-B
    Reverse signal
    Engine switch on (IG), shift lever in R
    7.5 to 14 V
    Engine switch on (IG), shift lever not in R
    Below 1 V
    I7-37 (CGND) - I6-4 (GND1)
    GR - W-B
    Rear television camera ground (shield)
    Always
    Below 1 Ω
    I7-38 (CV-) - I7-37 (CGND)
    W - GR
    Rear television camera ground
    Always
    Below 1 V

  5. E171712E22
    Using an oscilloscope, check waveform.
    Text in Illustration 
    *a
    Waveform 1
    *b
    Waveform 2
    *c
    Synchronized Signal
    *d
    Video Waveform

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.


    1. Waveform 1

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      I7-15 (CV+) - I7-37 (CGND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), camera lens is not covered, displaying an image.

    2. Waveform 2

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      I7-15 (CV+) - I7-37 (CGND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), camera lens is covered, blacking out the screen.


NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type) (Click here)

RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type) (Click here)

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
← PROBLEM SYMPTOMS TABLE (from Aug 2014)TERMINALS OF ECU (from Aug 2014) →