General
Symptom
|
Suspected Area
|
See page
|
When the shift lever is in R, the parking assist monitor image is not displayed (screen is not black).
|
Proceed to "ECU Power Source Circuit"
|
Click here
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
When the shift lever is in R, the parking assist monitor image is not displayed (screen is black).
|
Proceed to "Image from Camera for Parking Assist Monitor is Abnormal"
|
Click here
|
When the shift lever is not in R, the parking assist monitor image is displayed.
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
Parking Assist Monitor System Malfunction
Symptom
|
Suspected Area
|
See page
|
Estimated course lines are not displayed
|
Parking assist monitor screen display mode settings (Check that estimated course line display mode is selected)
|
-
|
Parking assist ECU (for LHD)
|
Click here
|
Parking assist ECU (for RHD)
|
Click here
|
"System initializing" is displayed.
|
Correct the steering angle neutral point (Initialization)
|
Click here
|
"System initializing" is displayed even after correcting the steering angle neutral point.
|
Spiral cable sub-assembly
|
Click here
|
Correct the steering angle neutral point (Initialization)
|
Click here
|
Steering angle setting (Calibration)
|
Click here
|
Parking assist ECU (for LHD)
|
Click here
|
Parking assist ECU (for RHD)
|
Click here
|
"System not ready" is displayed.
|
Parking assist ECU initialization (Calibration)
|
Click here
|
"System not ready" is displayed even after parking assist ECU initialization.
|
Parking assist ECU (for LHD)
|
Click here
|
Parking assist ECU (for RHD)
|
Click here
|
During parallel parking assist mode, the screen does not change even though the vehicle has moved.
|
If vehicle is driven in reverse at very low speed, screen may not change
|
-
|
During parallel parking assist mode, the screen changes even though the vehicle has not moved.
|
If vehicle is stopped for extended period of time, screen may change
|
-
|
Guide lines and buttons are not displayed for all parking assist monitor screen display modes
|
Proceed to "Guide Lines and Buttons are not Displayed for All Display Modes"
|
Click here
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
The guide lines and buttons remain displayed even though the luggage compartment door is open
|
Proceed to "Guide Lines and Buttons are not Displayed for All Display Modes"
|
Click here
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed
|
Proceed to "Guide Lines and Buttons are not Displayed for All Display Modes"
|
Click here
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
"CHK" message(s) are displayed on the "Signal Check" screen.
|
Proceed to ""CHK" message(s) are displayed on the SIGNAL CHECK screen"
|
Click here
|
A back door open warning message is displayed even after back door is closed.
|
Proceed to "Guide Lines and Buttons are not Displayed for All Display Modes"
|
Click here
|
Main body ECU (multiplex network body ECU)
|
Click here
|
Parking assist ECU (for LHD)
|
Click here
|
Parking assist ECU (for RHD)
|
Click here
|
When an image of the area behind the vehicle is displayed, the lines are misaligned (the image from the camera is tilted)
|
Back camera position setting (Calibration)
|
Click here
|