2013-2015 Land Cruiser Prado · Service Manual Steering

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Install the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


2. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
  1. Install the hole cover with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not fold back the boot part of the steering hole cover or extend it excessively. If it is extended excessively, return it to its original position.


3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

    HINT:
    Install the steering intermediate shaft to the inside of the vehicle.

  1. Install the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


4. INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL LH
  1. w/ KDSS:
    Install the apron seal with the 7 clips.

  1. w/o KDSS:
    Install the apron seal with the 4 clips.


5. INSTALL STEERING COLUMN ASSEMBLY
  1. Align the matchmarks on the steering intermediate shaft and steering column.

  1. Install the steering column with the 4 nuts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Install the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Attach the claws to connect the wire harness protector and wire harness.


6. INSTALL INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
(Click here)

7. INSTALL NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
(Click here)

8. INSTALL TRANSPONDER KEY AMPLIFIER (Transponder Key)
(Click here)

9. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

  1. Connect the connectors to the combination switch with spiral cable.


10. INSTALL STEERING COLUMN UPPER COVER
  1. Attach the claw to install the steering column upper cover.

  1. Attach the 4 clips to install the steering column upper cover to the instrument cluster finish panel.


11. INSTALL STEERING COLUMN LOWER COVER
  1. Attach the 2 claws to install the steering column lower cover.

  1. Install the 2 screws.


12. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. B181594
    Rotate the spiral cable sub-assembly with steering sensor counterclockwise slowly by hand until it feels firm.

    CAUTION:
    Do not turn the spiral cable sub-assembly with steering sensor by the airbag wire harness.

  1. B359176E01
    Rotate the spiral cable sub-assembly with steering sensor clockwise approximately 2.5 turns to align the marks so that the colored part or the flat cable shown in the illustration is visible.
    Text in Illustration 
    *A
    w/o Steering Heater
    *B
    w/ Steering Heater
    *1
    Alignment Mark
    *2
    Colored Part
    *3
    Flat Cable

    CAUTION:
    Do not turn the spiral cable sub-assembly with steering sensor by the airbag wire harness.

    HINT:
    The spiral cable sub-assembly with steering sensor can be rotated approximately 2.5 turns to both the left and right from the center position.


13. INSTALL STEERING WHEEL ASSEMBLY
(Click here)

14. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

15. INSTALL FRONT WHEEL LH

16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


17. CHECK SRS WARNING LIGHT
(Click here)
← REASSEMBLY (from Aug 2013)INSTALLATION (from Aug 2014) →