2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1501 Sub Fuel Sender Open Detected

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
Trouble code B1501 is only stored in vehicles equipped with a double tank.

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.
DTC Code
DTC Detection Condition
Trouble Area
B1501
The combination meter detects a fuel sender gauge malfunction.
  1. Harness or connector
  2. Combination meter assembly
  3. Fuel sender gauge assembly

WIRING DIAGRAM

E202183E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)
  1. Operate the intelligent tester according to the display and select the Data List (Click here).

Combination Meter 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Fuel Input
Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5
Fuel sender input value
Unit: L

OK:
Fuel amount value displayed on the intelligent tester is almost same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL TANK VENT TUBE ASSEMBLY)
  1. Disconnect the G6 meter connector.

  1. Disconnect the t1 gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-8 (L) - t1-4 (S)
    Always
    Below 1 Ω
    G6-23 (FE) - t1-5 (E)
    G6-21 (E2) - Body ground
    G6-8 (L) or t1-4 (S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FUEL TANK VENT TUBE ASSEMBLY
E201612E01
  1. Remove the fuel tank vent tube assembly.for 1GR-FE: (Click here)for 2TR-FE: (Click here)for 1KD-FTV: (Click here)for 5L-E: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (S) - 1
    Always
    Below 1 Ω
    5 (E) - 2
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Fuel Tank Vent Tube Assembly
    *b
    Component without harness connected
    (Fuel Tank Vent Tube Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2TR-FE)
    C
    NG (for 1KD-FTV)
    D
    NG (for 5L-E)
    E



B
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)

C
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)

D
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)

E
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
A


4. INSPECT FUEL SENDER GAUGE ASSEMBLY
A223156E02
  1. Remove the fuel sender gauge assembly.for 1GR-FE: (Click here)for 2TR-FE: (Click here)for 1KD-FTV: (Click here)for 5L-E: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Float level is F (upper)
12 to 18 Ω
Float level is E (lower)
405 to 415 Ω

Text in Illustration 
*a
Fuel Sender Gauge Assembly
*b
Float Level is F (Upper)
*c
Float Level is E (Lower)
Result 
Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 2TR-FE)
C
NG (for 1KD-FTV)
D
NG (for 5L-E)
E


B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← B1501 Sub Fuel Sender Open Detected (Aug 2013 – Jul 2014)B2660 Steering Wheel Switch Malfunction (Aug 2013 – Jul 2014) →