2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2660 Steering Wheel Switch Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This code is output when any steering pad switch is continuously on for a period of 60 seconds.
DTC Code
DTC Detection Condition
Trouble Area
B2660
The driving support switch control ECU detects a malfunction in the steering pad switch.
  1. Harness or connector
  2. Driving support switch control ECU
  3. Spiral cable sub-assembly
  4. Steering pad switch assembly

WIRING DIAGRAM

E201873E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Operate the intelligent tester according to the display and select the Data List (Click here).

D-SEAT SW 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Steering Wheel Menu Switch
MENU switch/OFF or ON
OFF: MENU switch off
-
ON: MENU switch on
Steering Wheel Enter Switch
ENTER switch/OFF or ON
OFF: ENTER switch off
-
ON: ENTER switch on
Steering Wheel Up Switch
UP/DOWN UP switch/OFF or ON
OFF: UP/DOWN UP switch off
-
ON: UP/DOWN UP switch on
Steering Wheel Down Switch
UP/DOWN DOWN switch/OFF or ON
OFF: UP/DOWN DOWN switch off
-
ON: UP/DOWN DOWN switch on

OK:
The value displayed on the intelligent tester changes with the actual steering pad switch operation.



NG
Go to step 2
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.E202523E01

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z8-2 (DISP) - z8-3 (GND1)
    MENU switch pushed
    Below 2.5 Ω
    ENTER switch pushed
    313 to 346 Ω
    UP/DOWN UP switch pushed
    3049 to 3370 Ω
    UP/DOWN DOWN switch pushed
    959 to 1060 Ω
    switch off
    95 to 105 kΩ

    Text in Illustration 
    *a
    Front view of wire harness connector (to spiral cable sub-assembly)
    *b
    MENU switch
    *c
    ENTER switch
    *d
    UP/DOWN UP switch
    *e
    UP/DOWN DOWN switch



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3. INSPECT HARNESS AND CONNECTOR (SPIRAL CABLE - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the G76 driving support switch control ECU connector.

  1. Disconnect the G40 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G40-9 (DISP) - G76-3 (SWI1)
    Always
    Below 1 Ω
    G40-10 (GND1) - G76-4 (SWI2)
    Always
    Below 1 Ω
    G40-9 (DISP) - G40-2 (ECC)
    Always
    10 kΩ or higher
    G40-9 (DISP) - G40-4 (EAU)
    Always
    10 kΩ or higher
    G40-9 (DISP) -G40-10 (GND1)
    Always
    10 kΩ or higher
    G40-9 (DISP) - Body ground
    Always
    10 kΩ or higher
    G40-10 (GND1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E202531E01
    Set the spiral cable to the center position (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-9
    Always
    Below 1 Ω
    A-3 - B-10
    Always
    Below 1 Ω
    A-2 - A-3
    Always
    10 kΩ or higher
    A-2 - A-6
    Always
    10 kΩ or higher
    A-2 - A-8
    Always
    10 kΩ or higher
    A-2 - Body ground
    Always
    10 kΩ or higher
    A-3 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Connector A
    *b
    Connector B



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)


← B1501 Sub Fuel Sender Open Detected (from Aug 2014)B2660 Steering Wheel Switch Malfunction (from Aug 2014) →