Cooling Box Circuit
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the cooler control switch sub-assembly is pushed, the No. 1 cooler blower motor sub-assembly and cooler magnet valve assembly controlled by the air conditioning amplifier assembly and air conditioning amplifier assembly (for the cooling box) operate. If the cooling box assembly does not operate when the cooler control switch sub-assembly is pushed, there may be a problem in the circuit shown below.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK HARNESS AND CONNECTOR (COOLING BOX - BATTERY AND BODY GROUND) |
Disconnect the T6 cooling box connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
T6-3 (ILL+) - Body ground
Headlight dimmer switch off
Below 1 V
T6-3 (ILL+) - Body ground
Headlight dimmer switch on
11 to 14 V
T6-2 (B) - Body ground
Ignition switch off
Below 1 V
T6-2 (B) - Body ground
Ignition switch ON
11 to 14 V
T6-8 (+B) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
T6-9 (L) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Cooling Box Assembly) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLING BOX) |
Disconnect the G25 and G24 amplifier connectors.
Disconnect the T6 cooling box connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G25-15 (COOL) - T6-4 (COL1)
Always
Below 1 Ω
G24-12 (SWCB) - T6-5 (ACT)
Always
Below 1 Ω
G25-15 (COOL) - Body ground
Always
10 kΩ or higher
G24-12 (SWCB) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY |
Remove the cooler control switch sub-assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Cooler control switch sub-assembly on
Below 1 Ω
1 - 2
Cooler control switch sub-assembly off
10 kΩ or higher
Apply battery voltage to the cooler control switch sub-assembly connector and check that the cooler control switch sub-assembly illuminates.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 3
Battery negative (-) → Terminal 4
LED illuminates
Battery positive (+) → Terminal 5
Battery negative (-) → Terminal 6
LED illuminates
|
|
||||
| OK | |
| 4. INSPECT NO. 1 COOLER BLOWER MOTOR SUB-ASSEMBLY |
Remove the No. 1 cooler blower motor sub-assembly (Click here).

Apply battery voltage to the No. 1 cooler blower motor sub-assembly and check that the No. 1 cooler blower motor sub-assembly operates smoothly.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
No. 1 cooler blower motor sub-assembly operates smoothly
|
|
||||
| OK | |
| 5. INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY |
Remove the No. 1 cooler wiring harness sub-assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-3 (ILL+) - B-5
Always
Below 1 Ω
A-2 (B) - E-2 (IG)
Always
Below 1 Ω
A-8 (+B) - E-1 (+B)
Always
Below 1 Ω
A-4 (COL1) - E-8 (CBT)
Always
Below 1 Ω
A-5 (ACT) - E-6 (CBI)
Always
Below 1 Ω
A-9 (L) - E-4 (GND)
Always
Below 1 Ω
A-9 (L) - B-6
Always
Below 1 Ω
A-2 (B) - B-3
Always
Below 1 Ω
B-4 - E-7 (LED)
Always
Below 1 Ω
B-2 - E-10 (SG)
Always
Below 1 Ω
B-1 - E-5 (SW)
Always
Below 1 Ω
A-2 (B) - C-1
Always
Below 1 Ω
C-2 - D-2
Always
Below 1 Ω
A-2 (B) - D-1
Always
Below 1 Ω
D-2 - E-9 (BLW)
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Vehicle Harness)
*b
Front view of wire harness connector
(to Cooler Control Switch Sub-assembly)
*c
Front view of wire harness connector
(to Cooler Magnet Valve Assembly)
*d
Front view of wire harness connector
(to No. 1 Cooler Blower Motor Sub-assembly)
*e
Front view of wire harness connector
(to Air Conditioning Amplifier Assembly [for Cooling Box])
|
|
||||
| OK | ||
| ||
