2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Cooling Box Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the cooler control switch sub-assembly is pushed, the No. 1 cooler blower motor sub-assembly and cooler magnet valve assembly controlled by the air conditioning amplifier assembly and air conditioning amplifier assembly (for the cooling box) operate. If the cooling box assembly does not operate when the cooler control switch sub-assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E202089E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (COOLING BOX - BATTERY AND BODY GROUND)

  1. E200628E01
    Disconnect the T6 cooling box connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T6-3 (ILL+) - Body ground
    Headlight dimmer switch off
    Below 1 V
    T6-3 (ILL+) - Body ground
    Headlight dimmer switch on
    11 to 14 V
    T6-2 (B) - Body ground
    Ignition switch off
    Below 1 V
    T6-2 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    T6-8 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T6-9 (L) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Cooling Box Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLING BOX)
  1. Disconnect the G25 and G24 amplifier connectors.

  1. Disconnect the T6 cooling box connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G25-15 (COOL) - T6-4 (COL1)
    Always
    Below 1 Ω
    G24-12 (SWCB) - T6-5 (ACT)
    Always
    Below 1 Ω
    G25-15 (COOL) - Body ground
    Always
    10 kΩ or higher
    G24-12 (SWCB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY

  1. E158415
    Remove the cooler control switch sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Cooler control switch sub-assembly on
    Below 1 Ω
    1 - 2
    Cooler control switch sub-assembly off
    10 kΩ or higher

  1. Apply battery voltage to the cooler control switch sub-assembly connector and check that the cooler control switch sub-assembly illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3
    Battery negative (-) → Terminal 4
    LED illuminates
    Battery positive (+) → Terminal 5
    Battery negative (-) → Terminal 6
    LED illuminates



NG
REPLACE COOLER CONTROL SWITCH SUB-ASSEMBLY (Click here)
OK


4. INSPECT NO. 1 COOLER BLOWER MOTOR SUB-ASSEMBLY

  1. E195920
    Remove the No. 1 cooler blower motor sub-assembly (Click here).

  1. Apply battery voltage to the No. 1 cooler blower motor sub-assembly and check that the No. 1 cooler blower motor sub-assembly operates smoothly.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    No. 1 cooler blower motor sub-assembly operates smoothly



NG
REPLACE NO. 1 COOLER BLOWER MOTOR SUB-ASSEMBLY (Click here)
OK


5. INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

  1. E194813E01
    Remove the No. 1 cooler wiring harness sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (ILL+) - B-5
    Always
    Below 1 Ω
    A-2 (B) - E-2 (IG)
    Always
    Below 1 Ω
    A-8 (+B) - E-1 (+B)
    Always
    Below 1 Ω
    A-4 (COL1) - E-8 (CBT)
    Always
    Below 1 Ω
    A-5 (ACT) - E-6 (CBI)
    Always
    Below 1 Ω
    A-9 (L) - E-4 (GND)
    Always
    Below 1 Ω
    A-9 (L) - B-6
    Always
    Below 1 Ω
    A-2 (B) - B-3
    Always
    Below 1 Ω
    B-4 - E-7 (LED)
    Always
    Below 1 Ω
    B-2 - E-10 (SG)
    Always
    Below 1 Ω
    B-1 - E-5 (SW)
    Always
    Below 1 Ω
    A-2 (B) - C-1
    Always
    Below 1 Ω
    C-2 - D-2
    Always
    Below 1 Ω
    A-2 (B) - D-1
    Always
    Below 1 Ω
    D-2 - E-9 (BLW)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vehicle Harness)
    *b
    Front view of wire harness connector
    (to Cooler Control Switch Sub-assembly)
    *c
    Front view of wire harness connector
    (to Cooler Magnet Valve Assembly)
    *d
    Front view of wire harness connector
    (to No. 1 Cooler Blower Motor Sub-assembly)
    *e
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly [for Cooling Box])



NG
REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Cooling Box Circuit (Aug 2013 – Jul 2014)Viscous Heater with Magnet Clutch Circuit (Aug 2013 – Jul 2014) →