2013-2015 Land Cruiser Prado · Service Manual Suspension

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure (for Europe):
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    P245/70R17 108S
    220 (2.2, 32)
    220 (2.2, 32)
    245/70R17 110S
    220 (2.2, 32)
    220 (2.2, 32)
    P265/65R17 110S
    220 (2.2, 32)
    220 (2.2, 32)
    265/65R17 112S
    220 (2.2, 32)
    220 (2.2, 32)
    P265/60R18 109H
    220 (2.2, 32)
    220 (2.2, 32)
    265/60R18 110H
    220 (2.2, 32)
    220 (2.2, 32)


    Cold Tire Inflation Pressure (for Eastern Europe and Russia):
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    245/70R17 110S
    200 (2.0, 29)
    200 (2.0, 29)
    265/65R17 112S
    200 (2.0, 29)
    200 (2.0, 29)
    265/60R18 110H
    200 (2.0, 29)
    200 (2.0, 29)


    Cold Tire Inflation Pressure (for General Export, Australia, G.C.C.):
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    245/70R17 110S
    200 (2.0, 29)
    200 (2.0, 29)
    265/65R17 112S
    200 (2.0, 29)
    200 (2.0, 29)
    265/60R18 110H
    200 (2.0, 29)
    200 (2.0, 29)

  1. C137874
    Using a dial indicator, check the tire runout.

    Standard tire runout:
    2.0 mm (0.0787 in.) or less


ROTATE TIRES

  1. C200706E03
    Rotate the tires as shown in the illustration.

    Torque:
    for steel wheel:
    112 N*m{ 1137 kgf*cm , 82 ft.*lbf }
    for aluminum wheel:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

    Text in Illustration 
    *a
    Front of the Vehicle
    *b
    for Vehicles with Spare Tire
    *c
    for Vehicles without Spare Tire


INSPECT WHEEL BALANCE

  1. C144019
    for Steel Wheel Type:
    Check and adjust the off-the-car balance.

    Standard Imbalance After Adjustment:
    12 g (0.0265 lb.) or less

    HINT:
    If necessary, check and adjust the on-the-car balance.

  1. for Aluminum Wheel Type:
    Check and adjust the off-the-car balance.

    Standard Imbalance After Adjustment:
    6.0 g (0.0132 lb.) or less


    C241067E02
    Text in Illustration 
    *a
    for 17 Inch Wheels
    *b
    for 18 Inch Wheels

    NOTICE:
    1. Using a cleaning detergent, remove dirt, oil and water from the surface where the balance weight is to be adhered.
    2. Do not touch the adhesive surface of the tape.
    3. Attach a sticking type balance weight to the flat surface (A) shown in the illustration.

      Width (A):
      25 mm (0.984 in.)

    4. Push the balance weight securely with your finger so that it securely adheres to the position.
    5. Do not reuse the balance weight.

    HINT:
    1. For 17 inch wheels, the outer side balance weight should be installed by clipping it to the rim.
    2. If necessary, check and adjust the on-the-car balance.


INSPECT FRONT AXLE HUB BEARING LOOSENESS
(Click here)

REMOVE FRONT AXLE HUB RUNOUT
(Click here)

INSPECT REAR AXLE SHAFT RUNOUT
(Click here)
← HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2013)DISPOSAL (from Aug 2013) →