B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The certification ECU generates a request signal and transmits the signal to the electrical key antenna (outside luggage). The electrical key antenna (outside luggage) detects that the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the back door, the signal is transmitted. DTC B27A8 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).| DTC Code |
DTC Detection Condition |
Trouble Area |
| B27A8 |
An open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
- Before replacing the certification ECU, refer to the Service Bulletin.
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK CONNECTOR CONNECTION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU and electrical key antenna (outside luggage).
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU) |
Disconnect the R16 antenna connector.
Disconnect the G39 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R16-1 (CLG5) - G39-19 (CLG8)
Always
Below 1 Ω
R16-2 (CLGB) - G39-20 (CG8B)
Always
Below 1 Ω
G39-19 (CLG8) - Body ground
Always
10 kΩ or higher
G39-20 (CG8B) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) |
![]() ![]() |
Remove the outside electrical key antenna (outside luggage) (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (CLG5) - 2 (CLGB)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. REPLACE CERTIFICATION ECU |
Temporarily replace the certification ECU with a new one (Refer to the Service Bulletin).
| NEXT | |
| 5. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B27A8 is not output.
|
|
||||
| OK | ||
| ||

