2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the electrical key antenna (outside luggage). The electrical key antenna (outside luggage) detects that the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the back door, the signal is transmitted. DTC B27A8 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).
DTC Code
DTC Detection Condition
Trouble Area
B27A8
An open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).
  1. Harness or connector
  2. Electrical key antenna (outside luggage)
  3. Certification ECU

WIRING DIAGRAM

B210706E05

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and electrical key antenna (outside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the R16 antenna connector.

  1. Disconnect the G39 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R16-1 (CLG5) - G39-19 (CLG8)
    Always
    Below 1 Ω
    R16-2 (CLGB) - G39-20 (CG8B)
    Always
    Below 1 Ω
    G39-19 (CLG8) - Body ground
    Always
    10 kΩ or higher
    G39-20 (CG8B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
B226391E01
  1. Remove the outside electrical key antenna (outside luggage) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (CLG5) - 2 (CLGB)
    Always
    Below 1 Ω



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK


4. REPLACE CERTIFICATION ECU
  1. Temporarily replace the certification ECU with a new one (Refer to the Service Bulletin).


NEXT


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A8 is not output.



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK

END (CERTIFICATION ECU IS DEFECTIVE)


← B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit (Aug 2013 – Jul 2014)All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate (Aug 2013 – Jul 2014) →