B2658 Short in Sensor with Motor Power Supply Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2658 |
A problem with the voltage supplied to the position control sensor. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2658 is not output.
|
|
||||
| OK | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the b1*1 or a1*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b5-5 (SSRS) - b1-2 (O/P)
Always
Below 1 Ω
b5-1 (SGND) - b1-3 (GND)
Always
Below 1 Ω
b5-5 (SSRS) - b5-1 (SGND)
Always
10 kΩ or higher
b5-5 (SSRS) - Body ground
Always
10 kΩ or higher
b5-1 (SGND) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a5-5 (SSRS) - a1-2 (O/P)
Always
Below 1 Ω
a5-1 (SGND) - a1-3 (GND)
Always
Below 1 Ω
a5-5 (SSRS) - a5-1 (SGND)
Always
10 kΩ or higher
a5-5 (SSRS) - Body ground
Always
10 kΩ or higher
a5-1 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT) |
Disconnect the b1*1 or a1*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
b1-2 (O/P) - b1-3 (GND)
Sliding switch on
4.8 to 5.1 V
for RHD Tester Connection
Switch Condition
Specified Condition
a1-2 (O/P) - a1-3 (GND)
Sliding switch on
4.8 to 5.1 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Slide Motor])
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the b2*1 or a2*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b5-3 (SSFV) - b2-2 (O/P)
Always
Below 1 Ω
b5-1 (SGND) - b2-3 (GND)
Always
Below 1 Ω
b5-3 (SSFV) - b5-1 (SGND)
Always
10 kΩ or higher
b5-3 (SSFV) - Body ground
Always
10 kΩ or higher
b5-1 (SGND) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a5-3 (SSFV) - a2-2 (O/P)
Always
Below 1 Ω
a5-1 (SGND) - a2-3 (GND)
Always
Below 1 Ω
a5-3 (SSFV) - a5-1 (SGND)
Always
10 kΩ or higher
a5-3 (SSFV) - Body ground
Always
10 kΩ or higher
a5-1 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT) |
Disconnect the b2*1 or a2*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
b2-2 (O/P) - b2-3 (GND)
Front vertical switch on
4.8 to 5.1 V
for RHD Tester Connection
Switch Condition
Specified Condition
a2-2 (O/P) - a2-3 (GND)
Front vertical switch on
4.8 to 5.1 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the b3*1 or a3*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b5-4 (SSRL) - b3-2 (O/P)
Always
Below 1 Ω
b5-1 (SGND) - b3-3 (GND)
Always
Below 1 Ω
b5-4 (SSRL) - b5-1 (SGND)
Always
10 kΩ or higher
b5-4 (SSRL) - Body ground
Always
10 kΩ or higher
b5-1 (SGND) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a5-4 (SSRL) - a3-2 (O/P)
Always
Below 1 Ω
a5-1 (SGND) - a3-3 (GND)
Always
Below 1 Ω
a5-4 (SSRL) - a5-1 (SGND)
Always
10 kΩ or higher
a5-4 (SSRL) - Body ground
Always
10 kΩ or higher
a5-1 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT) |
Disconnect the b3*1 or a3*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
b3-2 (O/P) - b3-3 (GND)
Lifter switch on
4.8 to 5.1 V
for RHD Tester Connection
Switch Condition
Specified Condition
a3-2 (O/P) - a3-3 (GND)
Lifter switch on
4.8 to 5.1 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])
|
|
||||
| OK | |
| 8. CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY |
Temporarily replace the separate type front seat cushion springs one at a time with a new or normally functioning one (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2658 is not output.
|
|
||||
| OK | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR) |
- *1: for LHD
- *2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the f1*1 or e1*2 motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
b5-11 (SSRR) - f1-2 (O/P)
Always
Below 1 Ω
b5-1 (SGND) - f1-3 (GND)
Always
Below 1 Ω
b5-11 (SSRR) - b5-1 (SGND)
Always
10 kΩ or higher
b5-11 (SSRR) - Body ground
Always
10 kΩ or higher
b5-1 (SGND) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
a5-11 (SSRR) - e1-2 (O/P)
Always
Below 1 Ω
a5-1 (SGND) - e1-3 (GND)
Always
Below 1 Ω
a5-11 (SSRR) - a5-1 (SGND)
Always
10 kΩ or higher
a5-11 (SSRR) - Body ground
Always
10 kΩ or higher
a5-1 (SGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT) |
Disconnect the f1*1 or e1*2 motor connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Switch Condition
Specified Condition
f1-2 (O/P) - f1-3 (GND)
Reclining switch on
4.8 to 5.1 V
for RHD Tester Connection
Switch Condition
Specified Condition
e1-2 (O/P) - e1-3 (GND)
Reclining switch on
4.8 to 5.1 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Separate Type Front Seatback Assembly [Reclining Motor])
|
|
||||
| OK | |
| 11. CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
Temporarily replace the separate type front seatbacks one at a time with a new or normally functioning one (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2658 is not output.
|
|
||||
| OK | ||
| ||
