2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2658 Short in Sensor with Motor Power Supply Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
DTC Code
DTC Detection Condition
Trouble Area
B2658
A problem with the voltage supplied to the position control sensor.
  1. Front power seat switch
  2. Separate type front seat cushion spring assembly
  3. Separate type front seatback assembly
  4. Harness or connector

WIRING DIAGRAM

B238259E01

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b1*1 or a1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-5 (SSRS) - b1-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b1-3 (GND)
    Always
    Below 1 Ω
    b5-5 (SSRS) - b5-1 (SGND)
    Always
    10 kΩ or higher
    b5-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-5 (SSRS) - a1-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a1-3 (GND)
    Always
    Below 1 Ω
    a5-5 (SSRS) - a5-1 (SGND)
    Always
    10 kΩ or higher
    a5-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)

  1. B238255E01
    Disconnect the b1*1 or a1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b1-2 (O/P) - b1-3 (GND)
    Sliding switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a1-2 (O/P) - a1-3 (GND)
    Sliding switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



NG
REPLACE FRONT POWER SEAT SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b2*1 or a2*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-3 (SSFV) - b2-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b2-3 (GND)
    Always
    Below 1 Ω
    b5-3 (SSFV) - b5-1 (SGND)
    Always
    10 kΩ or higher
    b5-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-3 (SSFV) - a2-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a2-3 (GND)
    Always
    Below 1 Ω
    a5-3 (SSFV) - a5-1 (SGND)
    Always
    10 kΩ or higher
    a5-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)

  1. B238255E03
    Disconnect the b2*1 or a2*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b2-2 (O/P) - b2-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a2-2 (O/P) - a2-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



NG
REPLACE FRONT POWER SEAT SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the b3*1 or a3*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-4 (SSRL) - b3-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - b3-3 (GND)
    Always
    Below 1 Ω
    b5-4 (SSRL) - b5-1 (SGND)
    Always
    10 kΩ or higher
    b5-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-4 (SSRL) - a3-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - a3-3 (GND)
    Always
    Below 1 Ω
    a5-4 (SSRL) - a5-1 (SGND)
    Always
    10 kΩ or higher
    a5-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)

  1. B238255E04
    Disconnect the b3*1 or a3*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    b3-2 (O/P) - b3-3 (GND)
    Lifter switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    a3-2 (O/P) - a3-3 (GND)
    Lifter switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])



NG
REPLACE FRONT POWER SEAT SWITCH (Click here)
OK


8. CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
  1. Temporarily replace the separate type front seat cushion springs one at a time with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 9
OK

END (REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

9. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
  1. *1: for LHD
  2. *2: for RHD
  1. Disconnect the b5*1 or a5*2 switch connector.

  1. Disconnect the f1*1 or e1*2 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    b5-11 (SSRR) - f1-2 (O/P)
    Always
    Below 1 Ω
    b5-1 (SGND) - f1-3 (GND)
    Always
    Below 1 Ω
    b5-11 (SSRR) - b5-1 (SGND)
    Always
    10 kΩ or higher
    b5-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    b5-1 (SGND) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    a5-11 (SSRR) - e1-2 (O/P)
    Always
    Below 1 Ω
    a5-1 (SGND) - e1-3 (GND)
    Always
    Below 1 Ω
    a5-11 (SSRR) - a5-1 (SGND)
    Always
    10 kΩ or higher
    a5-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    a5-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)

  1. B238255E02
    Disconnect the f1*1 or e1*2 motor connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    f1-2 (O/P) - f1-3 (GND)
    Reclining switch on
    4.8 to 5.1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    e1-2 (O/P) - e1-3 (GND)
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Separate Type Front Seatback Assembly [Reclining Motor])



NG
REPLACE FRONT POWER SEAT SWITCH (Click here)
OK


11. CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. Temporarily replace the separate type front seatbacks one at a time with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
REPLACE FRONT POWER SEAT SWITCH (Click here)
OK

END (REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY)


← B2653 Lifter Sensor Malfunction (from Aug 2014)B2658 Short in Sensor with Motor Power Supply Circuit (from Aug 2014) →