2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Image from Camera for Parking Assist Monitor is Abnormal

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The video signal from the rear television camera assembly is transmitted to the navigation receiver assembly.

WIRING DIAGRAM

E286150E02

INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

HINT:
Images may be unclear even in normal conditions if:
  1. Electrical devices are used in the cabin (noise may occur in the image).
  2. Accessories that generate radio waves have been installed (noise may occur in the image).
  3. The outer mirror switch assembly is operated (noise may occur in the image).
  4. The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
  5. The camera lens is dirty with snow, mud, etc.
  6. A strong beam of light, such as a sunbeam or headlight, hits the camera.
  7. It is too dark around the camera (at night etc.).
  8. The ambient temperature around the camera is either too high or too low.
  9. The vehicle is tilted at a steep angle.
  10. The rear television camera assembly lens is scratched.
  11. The rear television camera assembly lens has drops of water on it or the humidity is high.
  12. When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.


1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the H62 navigation receiver assembly connector.

  1. Disconnect the v2 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H62-7 (CA+) - v2-6 (CB+)
    Always
    Below 1 Ω
    H62-8 (V+) - v2-3 (CV+)
    Always
    Below 1 Ω
    H62-15 (CGND) - v2-5 (CGND)
    Always
    Below 1 Ω
    H62-16 (V-) - v2-2 (CV-)
    Always
    Below 1 Ω
    H62-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    H62-8 (V+) - Body ground
    Always
    10 kΩ or higher
    H62-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    H62-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E280620E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H62-15 (CGND) - Body ground
    Always
    Below 1 Ω
    H62-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H62-7 (CA+) - H62-15 (CGND)
    Engine switch on (ACC)
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E224537E14

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    H62-8 (V+) - H62-15 (CGND)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Engine switch on (IG)
    2. Waveform 2: Engine switch on (IG), screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Reverse Signal Circuit (from Aug 2014)Image from Camera for Parking Assist Monitor is Abnormal (from Aug 2014) →