2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Image from Camera for Side Monitor is Abnormal

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The display signal from the side television camera assembly is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2 via the parking assist ECU.
  1. *1: for Navigation Receiver Type
  2. *2: for Radio and Display Type

WIRING DIAGRAM

E285878E03

INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).

HINT:
Images are difficult to discern even in normal conditions if:
  1. Noise may occur in the image while adjusting or retracting the outer rear view mirror assembly.
  2. Noise may occur in the image depending on electrical devices used in the cabin.
  3. Noise may occur in the image if accessories that generate radio waves have been installed.
  4. The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
  5. The camera lens is dirty with snow, mud, etc.
  6. A strong beam of light, such as a sunbeam or headlight, hits the camera.
  7. It is too dark around the camera (at night etc.).
  8. The ambient temperature around the camera is either too high or too low.
  9. The vehicle is tilted at a steep angle.
  10. When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.
  11. When a strong light (such as when sunlight is reflected off a vehicle body) hits the camera, vertical streaks, a phenomenon particular to the camera, may appear in the image.
  12. In order to position the camera, a portion of the vehicle appears in the side monitor image. This is not a malfunction.
  13. Light from buildings or the taillights of vehicles may be reflected in the image when driving at night. This is not a malfunction.


1. CHECK SYMPTOMS
  1. Check the image from side television camera.

    Result 
    Result
    Proceed to
    Image from camera for passenger side monitor is abnormal
    A
    Image from camera for driver side monitor is abnormal
    B



B
Go to step 7
A


2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY)
  1. Disconnect the I7 parking assist ECU connector.

  1. Disconnect the J3*1 or K2*2 front passenger side outer rear view mirror assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I7-34 (SCV-) - J3-12 (SCV-)
    Always
    Below 1 Ω
    I7-10 (SCV+) - J3-6 (SCV+)
    Always
    Below 1 Ω
    I7-33 (SGND) - J3-13 (SGND)
    Always
    Below 1 Ω
    I7-32 (SCB+) - J3-5 (SCB+)
    Always
    Below 1 Ω
    I7-34 (SCV-) - Body ground
    Always
    10 kΩ or higher
    I7-10 (SCV+) - Body ground
    Always
    10 kΩ or higher
    I7-33 (SGND) - Body ground
    Always
    10 kΩ or higher
    I7-32 (SCB+) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I7-34 (SCV-) - K2-12 (SCV-)
    Always
    Below 1 Ω
    I7-10 (SCV+) - K2-6 (SCV+)
    Always
    Below 1 Ω
    I7-33 (SGND) - K2-13 (SGND)
    Always
    Below 1 Ω
    I7-32 (SCB+) - K2-5 (SCB+)
    Always
    Below 1 Ω
    I7-34 (SCV-) - Body ground
    Always
    10 kΩ or higher
    I7-10 (SCV+) - Body ground
    Always
    10 kΩ or higher
    I7-33 (SGND) - Body ground
    Always
    10 kΩ or higher
    I7-32 (SCB+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK PARKING ASSIST ECU

  1. E245958E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-33 (SGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I7-32 (SCB+) - I7-33 (SGND)
    Engine switch on (IG), wide view front and side monitor switch on
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A


4. CHECK FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY

  1. Measure the waveform of the front passenger side television camera assembly using an oscilloscope.E245725E30

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)
    *b
    Waveform A
    *c
    Waveform B
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    HINT:
    1. A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
      1. *1: for Navigation Receiver Type
      2. *2: for Radio and Display Type
    2. The video waveform changes according to the image sent by the side television camera assembly.

    Measurement Condition 
    Item
    Content
    Tester Connection
    I7-10 (SCV+) - I7-33 (SGND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    1. Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image
    2. Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen

    OK:
    Waveform is as shown in illustration.

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
Go to step 5
A

REPLACE PARKING ASSIST ECU (Click here)

5. REPLACE FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY
  1. Replace the front passenger side television camera assembly with a new or normally functioning one (Click here).


NEXT


6. CONFIRM SYMPTOMS
  1. Check if the same malfunction recurs when the side monitor screen is displayed.

    Result 
    Result
    Proceed to
    Malfunction does not reoccur (returns to normal)
    A
    Malfunction reoccurs
    B



B
REPLACE FRONT PASSENGER OUTER REAR VIEW MIRROR ASSEMBLY (Click here)
A

END (FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - DRIVER SIDE OUTER REAR VIEW MIRROR ASSEMBLY)
  1. Disconnect the I7 parking assist ECU connector.

  1. Disconnect the K2*1 or J3*2 driver side outer rear view mirror assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I7-31 (DCV-) - K2-12 (DCV-)
    Always
    Below 1 Ω
    I7-30 (DCV+) - K2-6 (DCV+)
    Always
    Below 1 Ω
    I7-29 (DGND) - K2-13 (DGND)
    Always
    Below 1 Ω
    I7-28 (DCB+) - K2-5 (DCB+)
    Always
    Below 1 Ω
    I7-31 (DCV-) - Body ground
    Always
    10 kΩ or higher
    I7-30 (DCV+) - Body ground
    Always
    10 kΩ or higher
    I7-29 (DGND) - Body ground
    Always
    10 kΩ or higher
    I7-28 (DCB+) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I7-31 (DCV-) - J3-12 (DCV-)
    Always
    Below 1 Ω
    I7-30 (DCV+) - J3-6 (DCV+)
    Always
    Below 1 Ω
    I7-29 (DGND) - J3-13 (DGND)
    Always
    Below 1 Ω
    I7-28 (DCB+) - J3-5 (DCB+)
    Always
    Below 1 Ω
    I7-31 (DCV-) - Body ground
    Always
    10 kΩ or higher
    I7-30 (DCV+) - Body ground
    Always
    10 kΩ or higher
    I7-29 (DGND) - Body ground
    Always
    10 kΩ or higher
    I7-28 (DCB+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK PARKING ASSIST ECU

  1. E245958E32
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I7-29 (DGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I7-28 (DCB+) - I7-29 (DGND)
    Engine switch on (IG), wide view front and side monitor switch on
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)
Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
REPLACE PARKING ASSIST ECU (Click here)
A


9. CHECK DRIVER SIDE OUTER REAR VIEW MIRROR ASSEMBLY

  1. Measure the waveform of the driver side television camera assembly using an oscilloscope.E245725E31

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)
    *b
    Waveform A
    *c
    Waveform A
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    HINT:
    1. A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
      1. *1: for Navigation Receiver Type
      2. *2: for Radio and Display Type
    2. The video waveform changes according to the image sent by the side television camera assembly.

    Measurement Condition 
    Item
    Content
    Tester Connection
    I7-30 (DCV+) - I7-29 (DGND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    1. Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image
    2. Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen

    OK:
    Waveform is as shown in illustration.

Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
Go to step 10
A

REPLACE PARKING ASSIST ECU (Click here)

10. REPLACE DRIVER SIDE TELEVISION CAMERA ASSEMBLY
  1. Replace the driver side television camera assembly with a new or normally functioning one (Click here).


NEXT


11. CONFIRM SYMPTOMS
  1. Check if the same malfunction recurs when the side monitor screen is displayed.

    Result 
    Result
    Proceed to
    Malfunction does not reoccur (returns to normal)
    A
    Malfunction reoccurs
    B



B
REPLACE DRIVER SIDE OUTER REAR VIEW MIRROR ASSEMBLY (Click here)
A

END (DRIVER SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)


← Image from Camera for Side Monitor is Abnormal (Aug 2013 – Jul 2014)PRECAUTION (from Aug 2013) →