2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

CALIBRATION

Troubleshooting · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


ADJUST SIDE MONITOR SYSTEM
  1. This side monitor system can be set from the diagnostic screen of the navigation receiver assembly*1 or radio and display receiver assembly*2.

  2. If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

    Part Name
    Operation
    Adjustment Item
    Proceed to
    Spiral cable sub-assembly
    1. Removal and installation of the spiral cable sub-assembly
    2. Removal and installation of the connector of the spiral cable sub-assembly
    3. Replacement
    Steering angle neutral point
    Click here
    Steering angle setting
    Click here
    Parking assist ECU
    Replacement
    Parking assist ECU initialization
    Click here
    Suspension, tires, etc.
    The vehicle height changes because of suspension or tire replacement
    Rear television camera optical axis (Camera position setting)
    Click here
    Side television camera optical axis (Camera position setting)
    Procedure 1
    Side television camera assembly
    1. Replacement
    2. Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.
    Side television camera optical axis (Camera position setting)
    Procedure 1
    Outer rear view mirror assembly
    Replacement
    Side television camera optical axis (Camera position setting)
    Procedure 1
    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type

    NOTICE:
    After the engine switch is turned off, the navigation receiver assembly*1 or radio and display receiver assembly*2 records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal  
    Condition
    Waiting Time
    Vehicle enrolled in G-BOOK system
    6 minutes
    Vehicle not enrolled in G-BOOK system
    1 minute

    HINT:
    The adjustment values stored while performing side monitor system calibration are stored in the parking assist ECU.


SIDE CAMERA SETTING (Procedure 1)

HINT:
Be sure to check for DTCs before performing this procedure (Click here).

  1. Preparation for adjustment

    1. Park the vehicle with the steering wheel centered.

    2. E181012E03
      Set a target bar for optical axis adjustment of the rear television camera.

      HINT:
      Only when adjusting the optical axis of the camera, create a target bar for adjustment.

      Dimension:
      Area
      Specification
      A
      990 to 1000 mm (3.25 to 3.28 ft.)
      B
      1995 to 2005 mm (6.45 to 6.58 ft.)

      Text in Illustration 
      *a
      Vehicle Center
      *b
      Target Bar for Back Camera Adjustment
      *c
      Vehicle End
      *d
      Front Side

      HINT:
      1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display assembly and choose a tape color which can be easily seen.
      2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
      3. Check that the back door is fully closed.

    3. Set a target bar for optical axis adjustment of the side television camera.

      HINT:
      Only when adjusting the optical axis of the camera, create a target bar for adjustment.


      1. for LHD:

        E180069E05

      2. for RHD:

        E180068E02
      Text in Illustration 
      *a
      Target Bar for Side Camera Adjustment
      *b
      Front Wheel Axis
      *c
      Front Side
      *d
      Vehicle Center

      Dimension:
      A
      B
      C
      D
      E
      F
      1183 mm
      (3.88 ft.)
      1181 mm
      (3.87 ft.)
      500 mm
      (1.64 ft.)
      500 mm
      (1.64 ft.)
      500 mm
      (1.64 ft.)
      180 mm
      (7.09 in.)

      HINT:
      Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-display assembly and choose a tape color which can be easily seen.

  2. Start diagnostic mode.

    1. w/ Navigation System: Click here
    2. w/o Navigation System: Click here

    NOTICE:
    Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever to P, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

    HINT:
    The displayed items may differ depending on vehicle specifications.


    1. E271944
      Select "Function Check/Setting" on the "Service Menu" screen.

    2. E271945
      Select "Camera Setting" on the "Function Check/Setting I" screen.

    3. E246954
      Select "Side Camera Setting" on the "Mode Setting" screen.

      HINT:
      To select a grayed out item, select and hold the item for 2 seconds or more.

    4. E285877
      Select "Next" on the "Signal Check" screen.

      NOTICE:
      1. When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.
      2. When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen (Click here).

      HINT:
      1. When the outer mirrors are retracted, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.
      2. If the screen does not change to the "Side Camera Position Setting" screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the "Signal Check" screen (Click here).
      3. If the screen does not change to the "Side Camera Position Setting" screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the "Signal Check" screen, replace the parking assist ECU (for LHD) (Click here), (for RHD) (Click here).

  3. E181004E02
    Side Camera Position Setting:

    HINT:
    Colors used on the "Side Camera Position Setting" screen

    Text in Illustration 
    *a
    Target Adjustment Bar for Side Camera Position Setting
    *b
    Red Frame
    *c
    Yellow Frame

    1. E246955E02
      Perform the roll angle adjustment.
      1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.

    2. Perform the vertical and horizontal position adjustment.

      1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.

    3. Select "Next" to display "Side Verify Mode".

  4. Side Verify Mode:

    1. E246956
      Check that the red cross and the target adjustment bar are aligned.

      HINT:
      If they are not aligned, select "Back" and perform "Side Camera Position Setting" again.

    2. Select "Next" to display "Side Camera Signal Check".

  5. Side Camera Signal Check (w/ Multi-terrain Monitor):

    1. E248973E01
      Select "OK" to store the side camera aiming adjustment value and change the screen to the "Service Menu" screen.

      HINT:
      1. When "OK" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.
      2. The adjustment value will not be stored unless "Back" is selected.

  6. Finish diagnostic mode.

    1. w/ Navigation System: Click here
    2. w/o Navigation System: Click here

← CALIBRATION (Aug 2013 – Jul 2014)PROBLEM SYMPTOMS TABLE (from Aug 2013) →