2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Reverse Signal Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E278684E05

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK VEHICLE SIGNAL (OPERATION CHECK)

  1. E278094
    Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (Click here)].

  1. Check that the display changes between ON and OFF according to the shift lever position.

    OK:
    Shift Lever Position
    Display
    R
    ON
    Except R
    OFF

    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E140414E85
    Disconnect the radio and display receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-2 (REV) - Body ground
    Engine switch on (IG), shift lever in R
    7.5 to 14 V
    H51-2 (REV) - Body ground
    Engine switch on (IG), shift lever not in R
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 3

C
Go to step 5
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the H51 radio and display receiver assembly connector.

  1. Disconnect the C40 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H51-2 (REV) - C40-1 (RL)
    Always
    Below 1 Ω
    H51-2 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

  1. E270424E11
    Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C40-2 (RB) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/neutral Position Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the H51 radio and display receiver assembly connector.

  1. Disconnect the C41 back-up light switch assembly connector.Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H51-2 (REV) - C41-1
    Always
    Below 1 Ω
    H51-2 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

  1. E270423E02
    Disconnect the back-up light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C41-2 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Back-up Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)


← Vehicle Speed Signal Circuit between Radio Receiver and Extension Module (from Aug 2014)Reverse Signal Circuit (from Aug 2014) →