Reverse Signal Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.- *1: for Automatic Transmission
- *2: for Manual Transmission
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
| 1. CHECK VEHICLE SIGNAL (OPERATION CHECK) |
Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (Click here).

Check that the display changes between ON and OFF according to the shift lever position.
OK Shift Lever Position
Display
R
ON
Except R
OFF
- HINT:
- This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
|
|
||||
| OK | ||
| ||
| 2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY |
![]() ![]() |
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
H51-2 (REV) - Body ground
Ignition switch ON, shift lever in R
7.5 to 14 V
H51-2 (REV) - Body ground
Ignition switch ON, shift lever not in R
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
Result Result
Proceed to
OK
A
NG (for Automatic Transmission)
B
NG (for Manual Transmission)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY) |
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the C40 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H51-2 (REV) - C40-1 (RL)
Always
Below 1 Ω
H51-2 (REV) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY) |
Disconnect the park/neutral position switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C40-2 (RB) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Park/neutral Position Switch Assembly)
Result Result
Proceed to
OK (for A343F)
A
OK (for A750F)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY) |
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the C41 back-up light switch assembly connector.Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H51-2 (REV) - C41-1
Always
Below 1 Ω
H51-2 (REV) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY) |
Disconnect the back-up light switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C41-2 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Back-up Light Switch Assembly)
| Result |
Proceed to |
| OK (for R150F) |
A |
| OK (for RA61F) |
B |
| OK (for G52F) |
C |
| NG |
D |
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||

