2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

USB Audio System Recognition/Play Error

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E280102E17

INSPECTION PROCEDURE

HINT:
  1. When a large amount of data is in a USB device, it may take a while to before play begins.
  2. When using a USB device, files that are copy protected or encrypted cannot be played.
  3. When files are not played in the sorted order, perform the following procedure before inspection.
    1. Add numbers in front of the file names.
    2. Put the files in a folder and copy the folder data to the USB device.


1. CHECK USB DEVICE OR "iPod"
  1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

  1. Check if playable files are present on the USB device or "iPod".

    HINT:
    Refer to System Description for playable files (Click here).

  1. Check if the USB device is a compatible format or "iPod" is a compatible version.

    HINT:
    Refer to System Description for compatible formats and versions (Click here).

    Result 
    Result
    Proceed to
    No playable files exist, or incompatible device format or version
    A
    Playable files exist, and compatible device format or version
    B



B
Go to step 3
A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the H58 navigation receiver assembly connector.

  1. Disconnect the H68 No. 1 stereo jack adapter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H58-1 (USV1) - H68-1 (USV1)
    Always
    Below 1 Ω
    H58-2 (US1-) - H68-2 (US1-)
    Always
    Below 1 Ω
    H58-3 (US1+) - H68-3 (US1+)
    Always
    Below 1 Ω
    H58-4 (UGD1) - H68-4 (UGD1)
    Always
    Below 1 Ω
    H58-5 (USG1) - H68-5 (USG1)
    Always
    Below 1 Ω
    H58-1 (USV1) - Body ground
    Always
    10 kΩ or higher
    H58-2 (US1-) - Body ground
    Always
    10 kΩ or higher
    H58-3 (US1+) - Body ground
    Always
    10 kΩ or higher
    H58-4 (UGD1) - Body ground
    Always
    10 kΩ or higher
    H58-5 (USG1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E278189E09
    Reconnect the H58 navigation receiver assembly connector.

  1. Disconnect the No. 1 stereo jack adapter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H68-1 (USV1) - H68-4 (UGD1)
    Engine switch on (ACC)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
  1. Delete all files in the USB device or "iPod" and format/ restore it.

    NOTICE:
    Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.

  1. Save the data again and check if it can be played on the in-vehicle device.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

END (USB OR "iPod" IS DEFECTIVE)

5. REPLACE USB DEVICE OR "iPod"
  1. Turn the engine switch off.

  1. Turn the engine switch on (ACC).

  1. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

    HINT:
    1. If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
    2. Refer to System Description for compatible formats and versions (Click here).


NEXT


6. CHECK USB DEVICE OR "iPod"
  1. Check if USB device or "iPod" is recognized by navigation receiver, or if information such as track, artist and album names are displayed on screen.

    OK:
    USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE


← Portable Player cannot be Registered (from Aug 2014)USB Audio System Recognition/Play Error (from Aug 2014) →