U0235 Lost Communication with Cruise Control Front Distance Range Sensor
Diagnostic trouble codes · Vehicles built from Aug 2013
DESCRIPTION
The millimeter wave radar sensor assembly and driving support ECU transmit the data for general vehicle control and the diagnosis function through the communication line.The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U0235 |
While the vehicle speed is 50 km/h (31 mph) or more with the cruise control switch on, a communication stop between the millimeter wave radar sensor and driving support ECU continues for 1 second or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When the driving support ECU is replaced with a new one, initialization must be performed (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC.
- When the driving support ECU is replaced with a new one, initialization must be performed (Click here).
| 1. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BATTERY AND BODY GROUND) |
- NOTICE:
- A DTC is stored when the following inspection is performed. Be sure to clear the DTC after performing this inspection.
Disconnect the G119 ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage :
Tester Connection
Switch Condition
Specified Condition
G119-30 (B) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-25 (GND) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Driving Support ECU) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BODY GROUND) |
Disconnect the A15 sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A15-2 (SGND) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR) |
Disconnect the G119 ECU connector.
Disconnect the A15 sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G119-18 (CA1N) - A15-3 (CA1N)
Always
Below 1 Ω
G119-18 (CA1N) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK DRIVING SUPPORT ECU |
- NOTICE:
- A DTC is stored when the following inspection is performed. Be sure to clear the DTC after performing this inspection.
Disconnect the A15 sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage :
Tester Connection
Switch Condition
Specified Condition
G119-18 (CA1N) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Component with harness connected
(Driving Support ECU)
|
|
||||
| OK | |
| 5. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Replace the millimeter wave radar sensor assembly (Click here).
| NEXT | |
| 6. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Adjust the millimeter wave radar sensor assembly (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Clear the DTCs (Click here).
Perform the following to make sure the DTC detection conditions are met.
- HINT:
- If the detection conditions are not met, the system cannot detect the malfunction.
Drive the vehicle at a speed of 50 km/h (31 mph) or more.
Turn the cruise control switch on.
Check for DTCs (Click here).
- OK:
- DTC U0235 is not output.
|
|
||||
| OK | ||
| ||
