2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

U1102 Lost Communication with Radar Sensor

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU transmit the data for general vehicle control and the diagnosis function through the communication line.
The driving support ECU estimates the curve information based on the signal from the steering wheel and yaw rate sensor.
The driving support ECU transmits the current vehicle speed and estimates curve information to the millimeter wave radar sensor assembly.
DTC Code
DTC Detection Condition
Trouble Area
U1102
While the vehicle speed is 50 km/h (31 mph) or more with the cruise control switch on, a communication stop between the millimeter wave radar sensor and driving support ECU continues for 1 second or more.
  1. Harness or connector
  2. Driving support ECU
  3. Millimeter wave radar sensor assembly

WIRING DIAGRAM

E192828E11

INSPECTION PROCEDURE

NOTICE:
  1. When the driving support ECU is replaced with a new one, initialization must be performed (Click here).
  2. When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  4. Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC.


1. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BATTERY AND BODY GROUND)

NOTICE:
A DTC is stored when the following inspection is performed. Be sure to clear the DTC after performing this inspection.

  1. E178319E06
    Disconnect the A15 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Switch Condition
    Specified Condition
    A15-5 (IGB) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-2 (SGND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BODY GROUND)

  1. E178436E05
    Disconnect the G119 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G119-25 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU)
  1. Disconnect the A15 sensor connector.

  1. Disconnect the G119 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-4 (CA1P) - G119-40 (CA1P)
    Always
    Below 1 Ω
    A15-4 (CA1P) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


Go to step 2

4. REPLACE DRIVING SUPPORT ECU
  1. Replace the driving support ECU (Click here).


NEXT


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Perform the following to make sure the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the system cannot detect the malfunction.

    1. Drive the vehicle at a speed of 50 km/h (31 mph) or more.

    2. Turn the cruise control switch on.

  1. Check for DTCs (Click here).

    OK:
    DTC U1102 is not output.



NG
REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (Click here)
OK

END (DRIVING SUPPORT ECU IS DEFECTIVE)


← U0235 Lost Communication with Cruise Control Front Distance Range Sensor (from Aug 2013)Cruise Control Switch Circuit (Aug 2013 – Jul 2014) →