2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

NOTICE:
  1. When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly or cylinder head sub-assembly, it is necessary to replace the injection pipe sub-assemblies with new ones.
  2. When replacing the fuel supply pump assembly, common rail assembly, cylinder block sub-assembly, cylinder head sub-assembly, cylinder head gasket or timing gear case assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.
  3. After removing the injection pipe sub-assemblies and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

3. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

4. DISCONNECT WIRE HARNESS

  1. A245686
    Remove the bolt and disconnect the wire harness.

  1. A246260
    for LHD:
    Remove the bolt and disconnect the wire harness.

  1. Detach the 5 clamps and disconnect the wire harness from the cowl top panel.


5. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A239598
    Disconnect the manifold absolute pressure sensor connector and vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.


6. REMOVE EMISSION CONTROL VALVE BRACKET

  1. A239639
    Remove the bolt and emission control valve bracket.


7. REMOVE THROTTLE BODY BRACKET

  1. A244614
    Remove the 3 bolts and throttle body bracket.


8. REMOVE NO. 1 GAS FILTER

  1. A244608
    Disconnect the vacuum hose and remove the No. 1 gas filter from the gas filter bracket.


9. REMOVE GAS FILTER BRACKET

  1. A246247
    Detach the clamp and disconnect the wire harness.

  1. A244609
    Remove the bolt and gas filter bracket.


10. REMOVE INTAKE AIR CONNECTOR

  1. A245684
    Remove the 3 bolts, intake air connector and gasket.


11. REMOVE NO. 1 FUEL PIPE
  1. Disconnect the No. 2 fuel pipe (Click here).

  1. Remove the 4 bolts, union bolt, gasket and No. 1 fuel pipe.

    A239663E01

    Text in Illustration 
    *1
    No. 2 Fuel Pipe
    -
    -
    V100136
    Union Bolt
    -
    -


12. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A239621
    Remove the bolt, nut and 2 No. 2 injection pipe clamps.

  1. A239619E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe sub-assembly.
    Text in Illustration 
    *a
    Common Rail Assembly Side
    *b
    Injector Assembly Side


13. REMOVE NO. 2 FUEL PIPE

  1. A329755
    Using a 6 mm hexagon wrench, remove the union bolt and gasket.
    Text in Illustration 
    V100135
    Union Bolt
    V100136
    Fuel Check Valve
    V100137
    Bolt

  1. Remove the fuel check valve and gasket.

  1. Remove the bolt and No. 2 fuel pipe.


14. REMOVE NO. 3 NOZZLE LEAKAGE PIPE

  1. A239624
    Disconnect the 2 fuel hoses.
    Text in Illustration 
    V100136
    Fuel Check Valve

  1. Remove the 2 bolts.

  1. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.


15. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A329756
    Remove the 2 bolts.
    Text in Illustration 
    V100136
    Union Bolt

  1. Remove the union bolt, gasket and No. 2 nozzle leakage pipe assembly.


16. REMOVE VACUUM CONTROL VALVE SET
  1. Disconnect the 2 vacuum switching valve connectors.

  1. A244983
    Disconnect the 3 vacuum hoses, and then remove the 2 bolts and vacuum control valve set.


17. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A227248E01
    Using SST, remove the oil filter.
    SST
    09228-07501  


18. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the pressure discharge valve connector.

  1. A239630
    Remove the 2 bolts and common rail assembly.

    NOTICE:
    Do not remove the pressure discharge valve or fuel pressure sensor.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →