2013-2015 Land Cruiser Prado · Service Manual Brake

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

If any of the following is detected, the ABS warning light remains on.
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and skid control ECU.
  4. The anti-lock brake system is defective.
  5. The voltage at terminal IG1 is high.
  6. The rear differential is locked.*
  1. *: w/ Rear Differential Lock

HINT:
It may not be possible to use the intelligent tester when the skid control ECU is abnormal.


WIRING DIAGRAM

C216792E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check the skid control ECU connector connection.

    OK:
    The 2 connectors are securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2. CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


4. READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    Ignition switch ON: 11 to 14 V
    -

  1. Check the voltage output from the skid control ECU displayed on the intelligent tester.

    OK:
    The output voltage displayed on the intelligent tester is within 11 to 14 V.



NG
Go to step 7
OK


5. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    w/ Rear Differential Lock: Rear differential free
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
Go to step 9
OK


6. READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light/ ON or OFF
    OFF
    -

  1. When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON/OFF
    Observe the combination meter.
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C
    OFF
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

7. CHECK TERMINAL VOLTAGE (IG1)
  1. Disconnect the A7 skid control ECU connector.

  1. C214161E28
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
  1. Disconnect the A7 and A8 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A7-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A8-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
  1. Disconnect the A7 skid control ECU connector.

  1. Disconnect the G53 four wheel drive control ECU connector.

  1. w/ Rear Differential Lock:Disconnect the E2 rear differential lock detection switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Rear Differential Lock)
    A
    OK (w/ Rear Differential Lock)
    B
    NG
    C



B
Go to step 11

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


10. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. Connect the G53 four wheel drive control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)

11. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
  1. Remove the rear differential lock detection switch (Click here).

  1. C214518E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (GND) - 2 (+B)
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Differential Lock Detection Switch)



NG
REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) (Click here)
OK


12. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. Connect the G53 four wheel drive control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)


← ABS Warning Light Remains ON (Aug 2013 – Jul 2014)ABS Warning Light does not Come ON (Aug 2013 – Jul 2014) →