Brake Warning Light Remains ON
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Parking Brake SW
Parking brake switch/ ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.
- OK:
- When the parking brake is operated, the display changes as shown above.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Brake Warning Light
Brake warning light/ ON or OFF
ON: Warning light on
OFF: Warning light off
-
When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (Click here).
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Brake Warning Light
Brake warning light
Warning light ON/OFF
Observe the combination meter.
Result Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
OFF
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. INSPECT PARKING BRAKE SWITCH |
Disconnect the G77 parking brake switch connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - Body ground
Parking brake applied
(Switch pin not pushed in)
Below 1 Ω
Parking brake released
(Switch pin pushed in)
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Parking Brake Switch)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU) |
Disconnect the G77 parking brake switch connector.
Remove the main body ECU (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G77-1 - A-12 (PKB)
Always
Below 1 Ω
G77-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
