2013-2015 Land Cruiser Prado · Service Manual Brake

VSC OFF Indicator Light Remains ON

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Operation of the VSC OFF switch changes the vehicle between normal mode, TRC OFF mode and VSC OFF mode. During normal mode, pressing the VSC OFF switch for a short amount of time changes vehicle to TRC OFF mode. When the vehicle is stopped, pressing the VSC OFF switch for 3 seconds or more changes the vehicle to VSC OFF mode.
  1. When the transfer is in L4, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.
  2. w/ Rear Differential Lock:
    When the rear differential is locked, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.

WIRING DIAGRAM

C215188E04

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
  2. As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID CSW CIRCUIT)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-9 (CSW) - Body ground
    VSC OFF switch not pushed in
    10 kΩ or higher
    VSC OFF switch pushed in
    Below 1 Ω



NG
Go to step 5
OK


3. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    w/ Rear Differential Lock: Rear differential free
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
Go to step 7
OK


4. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode/ Normal, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC OFF mode
    VSC OFF: VSC OFF mode
    -

  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    Display changes according to switch operation.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

5. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - VSC OFF SWITCH)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the G9 VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-9 (CSW) - G9-6
    Always
    Below 1 Ω
    A7-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    G9-3 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).

  1. C215409E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 - 3
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration  
    *a
    Component without harness connected
    (VSC OFF Switch)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE VSC OFF SWITCH (Click here)

7. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID EXI3 CIRCUIT)
  1. Disconnect the A7 skid control ECU connector.

  1. Disconnect the G53 four wheel drive control ECU connector.

  1. w/ Rear Differential Lock:Disconnect the E2 rear differential lock detection switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Rear Differential Lock)
    A
    OK (w/ Rear Differential Lock)
    B
    NG
    C



B
Go to step 9

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


8. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. Connect the G53 four wheel drive control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)

9. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
  1. Remove the rear differential lock detection switch (Click here).

  1. C214518E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (GND) - 2 (+B)
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Differential Lock Detection Switch)



NG
REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) (Click here)
OK


10. CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A7 skid control ECU connector.

  1. C214161E32
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-40 (EXI3) - Body ground
    Ignition switch ON
    w/ Rear Differential Lock: Rear differential free
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)


← TRC OFF Indicator Light does not Come ON (from Aug 2014)VSC OFF Indicator Light Remains ON (from Aug 2014) →