2013-2015 Land Cruiser Prado · Service Manual Brake

Downhill Assist Control Indicator Light Remains ON

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the downhill assist control switch is turned on, the downhill assist control function is available and the downhill assist control indicator light illuminates.

WIRING DIAGRAM

Refer to Downhill Assist Control Indicator Light does not Come ON (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. INSPECT DOWNHILL ASSIST CONTROL SWITCH
  1. Remove the downhill assist control switch (Click here).

  1. C215496E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 4
    Not pushed in
    10 kΩ or higher
    Pushed in
    Below 1 Ω

    Text in Illustration  
    *a
    Component without harness connected
    (Downhill Assist Control Switch)



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU HDCS CIRCUIT)
  1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the G158 downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-44 (HDCS) - G158-4
    Always
    Below 1 Ω
    A7-44 (HDCS) or G158-4 - Body ground
    Always
    10 kΩ or higher
    G158-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Downhill Assist Control Light
    Downhill assist control indicator light
    Indicator light ON/OFF
    Observe the combination meter.

  1. When performing the Downhill Assist Control Light Active Test, check Downhill Assist Control Light in the Data List (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control Light
    Downhill assist control indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C
    OFF
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← Slip Indicator Light does not Come ON (from Aug 2014)Downhill Assist Control Indicator Light Remains ON (from Aug 2014) →