2013-2015 Land Cruiser Prado · Service Manual Steering

C15F0 VFC Solenoid Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This circuit supplies electric power to the power steering solenoid valve.
The power steering ECU controls the output current to the power steering solenoid valve in accordance with the steering angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.
DTC Code
DTC Detection Condition
Trouble area
C15F0
A short or open in the solenoid valve circuit
  1. Harness or connector
  2. Vane pump assembly
  3. Power steering ECU assembly

WIRING DIAGRAM

C210556E04

INSPECTION PROCEDURE


1. READ VALUE USING GTS (SOLENOID CURRENT)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / PPS / Data List.

    PPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solenoid Current
    Solenoid Current/
    Min.: 0 mA
    Max.: 1000 mA
    200 to 950 mA
    The engine is running and the steering wheel is being turned.

    OK:
    The normal condition value is displayed the GTS.



NG
Go to step 2
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

2. CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - POWER STEERING SOLENOID VALVE)
  1. Disconnect the power steering ECU and power steering solenoid valve connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G46-7 (SOF+) - C38-2 (SOF+)
    Always
    Below 1 Ω
    G46-8 (SOF-) - C38-1 (SOF-)
    G46-7 (SOF+) - Body ground
    Always
    10 kΩ or higher
    G46-8 (SOF-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT POWER STEERING SOLENOID VALVE ASSEMBLY
C179951E05
  1. Disconnect the power steering solenoid valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SOF-) - 2 (SOF+)
    20°C (68°F)
    6.7 to 7.3 Ω

  1. Connect the battery positive (+) lead with a 21 W bulb to terminal 2 (SOF+) and the negative (-) lead to terminal 1 (SOF-) of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D
    Text in Illustration 
    *a
    Component without harness connected
    (Power Steering Solenoid Valve)



B
REPLACE VANE PUMP ASSEMBLY (Click here)

C
REPLACE VANE PUMP ASSEMBLY (Click here)

D
REPLACE VANE PUMP ASSEMBLY (Click here)
A

REPLACE POWER STEERING ECU ASSEMBLY (Click here)


← C1544 High Engine Revolution Signal (from Aug 2014)C15F0 VFC Solenoid Circuit (from Aug 2014) →