2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL FUEL TANK TO FILLER PIPE HOSE

  1. A220824E01
    Align the fuel tank side mark with the hose side mark.
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Hose Side Mark

  1. Install the fuel tank to filler pipe hose to the fuel tank.


2. INSTALL NO. 3 FUEL TANK PROTECTOR
  1. Install the No. 3 fuel tank protector and attach the 4 clamps.

  1. Install the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


3. INSTALL FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)
  1. Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.

  1. A220825E01
    Align the protrusion of the fuel tank vent tube with the groove of the fuel tank.
    Text in Illustration 
    *1
    Protrusion
    *2
    Groove

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Install the fuel tank vent tube to the fuel tank.

  1. Put a new retainer on the fuel tank. While holding the fuel tank vent tube, tighten the retainer one complete turn by hand.

    Text in Illustration 
    *1
    Start Mark (Fuel Tank Side)
    *2
    Start Mark (Retainer Side)

    HINT:
    A220826E01
    Make sure the start marks on the retainer and fuel tank are aligned and then tighten the retainer.

  1. A243483E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Hold the fuel tank vent tube assembly upright by hand to ensure that the gasket is not moved out of position.
    2. Engage the claws of SST securely with the retainer holes to secure SST.
    3. Install SST while pressing the claws of SST against the retainer (toward the center of SST).

  1. A243481E01
    Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.
    SST
    09808-14030  
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Retainer Side Mark

    HINT:
    Fit the tips of SST onto the ribs of the retainer.


4. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)
  1. Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.

  1. A220825E01
    Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.
    Text in Illustration 
    *1
    Protrusion
    *2
    Groove

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Install the fuel suction with pump and gauge tube to the fuel tank.

  1. Put a new retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.

    Text in Illustration 
    *1
    Start Mark (Fuel Tank Side)
    *2
    Start Mark (Retainer Side)

    HINT:
    A220826E01
    Make sure the start marks on the retainer and fuel tank are aligned and then tighten the retainer.

  1. A243483E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Hold the fuel suction with pump and gauge tube assembly upright by hand to ensure that the gasket is not moved out of position.
    2. Engage the claws of SST securely with the retainer holes to secure SST.
    3. Install SST while pressing the claws of SST against the retainer (toward the center of SST).

  1. A243481E01
    Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.
    SST
    09808-14030  
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Retainer Side Mark

    HINT:
    Fit the tips of SST onto the ribs of the retainer.


5. INSTALL FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

  1. A223113
    Install the fuel return tube and fuel tank main tube with the 2 fuel tube joint clips.

    NOTICE:

    1. A118171E07
      Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the fuel tube joint clips are on the collars of the fuel tube joints.
    4. After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
      Text in Illustration 
      *1
      Fuel Tube Joint
      *2
      O-Ring
      *3
      Fuel Tube
      *4
      Fuel Tube Joint Clip
      *a
      CORRECT
      *b
      INCORRECT

  1. Install the fuel return tube and fuel tank main tube to the fuel tank.


6. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223115
    Install the fuel tank main tube, fuel return tube and No. 2 fuel main tube with the 3 fuel tube joint clips.

    NOTICE:

    1. A118171E07
      Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the fuel tube joint clips are on the collars of the fuel tube joints.
    4. After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
      Text in Illustration 
      *1
      Fuel Tube Joint
      *2
      O-Ring
      *3
      Fuel Tube
      *4
      Fuel Tube Joint Clip
      *a
      CORRECT
      *b
      INCORRECT

  1. Install the fuel tank main tube to the fuel tank.

  1. Install the fuel return tube to the fuel tank and attach the clamp.

  1. Install the No. 2 fuel main tube to the fuel tank and attach the clamp.


7. INSTALL NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A223242
    Install the No. 4 fuel main tube and fuel suction tube with the 2 fuel tube joint clips.

    NOTICE:

    1. A118171E07
      Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the fuel tube joint clips are on the collars of the fuel tube joints.
    4. After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
      Text in Illustration 
      *1
      Fuel Tube Joint
      *2
      O-Ring
      *3
      Fuel Tube
      *4
      Fuel Tube Joint Clip
      *a
      CORRECT
      *b
      INCORRECT

  1. Install the fuel suction tube to the fuel tank and attach the clamp.

  1. Install the No. 4 fuel main tube to the fuel tank and attach the clamp.


8. INSTALL FUEL TANK CUSHION
  1. Install 3 new fuel tank cushions to the fuel tank.


9. INSTALL FUEL TANK SUB-ASSEMBLY
  1. Set the fuel tank on a transmission jack and lift up the transmission jack.

    NOTICE:
    Do not allow the fuel tank to contact the vehicle, especially the differential.

  1. Install the 2 fuel tank bands with the 2 pins and 2 clips.

  1. Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


10. CONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Connect the fuel tank to filler pipe hose to the filler pipe.


11. CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)
  1. Connect the fuel tank breather tube (Click here).


12. CONNECT FUEL CUT OFF TUBE (for Single Tank Type)

13. CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)
  1. Connect the fuel tank breather tube (Click here).


14. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
  1. Connect the fuel return tube and No. 2 fuel main tube (Click here).


15. CONNECT FUEL CUT OFF TUBE (for Double Tank Type)
  1. Connect the fuel cut off tube (Click here).


16. CONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)
  1. Connect the No. 4 fuel main tube and fuel suction tube (Click here).


17. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

18. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

19. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

20. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
  1. Install the No. 1 fuel tank protector with the 6 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. for Half Cover Type:
    Install the No. 1 fuel tank protector with the 4 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


21. INSTALL REAR FLOOR SERVICE HOLE COVER
  1. Connect the fuel pump and fuel sender gauge connector.

  1. Install the rear floor service hole cover with the 3 screws.


22. INSTALL REAR SEAT ASSEMBLY LH
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Install the rear seat assembly LH (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type LH Side:
    Install the rear seat assembly LH (Click here).


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


24. BLEED AIR FROM FUEL SYSTEM
  1. w/ DPF (Click here)
  2. w/o DPF (Click here)

25. INSPECT FOR FUEL LEAK
  1. w/ DPF (Click here)
  2. w/o DPF (Click here)
← REMOVAL (from Aug 2014)INSTALLATION (from Aug 2014) →