INSTALLATION
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- NOTICE:
- When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly or cylinder head sub-assembly, it is necessary to replace the injection pipe sub-assemblies with new ones.
- When replacing the fuel supply pump assembly, common rail assembly, cylinder block sub-assembly, cylinder head sub-assembly, cylinder head gasket or timing gear case assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.
- After removing the injection pipe sub-assemblies and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
- When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly or cylinder head sub-assembly, it is necessary to replace the injection pipe sub-assemblies with new ones.
| 1. INSTALL FUEL SUPPLY PUMP ASSEMBLY |
Check that the injection gear in the timing gear case assembly moves back and forth smoothly.

Install a new O-ring to the fuel supply pump assembly.
Apply a light coat of engine oil to the O-ring.
Align the groove of the injection gear with the set key on the drive shaft.

Install the fuel supply pump assembly with the 2 nuts.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Install a new O-ring.
Using SST, hold the crankshaft pulley and install the set nut.

- SST
- 09213-58014
09330-00021
- Torque:
- 64 N*m{ 650 kgf*cm , 47 ft.*lbf }
Install the pump drive shaft pulley and No. 2 camshaft timing pulley flange with the 4 bolts.

- Torque:
- 31 N*m{ 316 kgf*cm , 23 ft.*lbf }
Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.

- Standard thrust clearance (reference):
- 0.15 to 0.55 mm (0.00590 to 0.0217 in.)
Connect the suction control valve connector and fuel temperature sensor connector to the fuel supply pump assembly.
Connect the 2 fuel hoses.
| 2. INSTALL NO. 1 INJECTION PUMP PROTECTOR |
Install the No. 1 injection pump protector with the 2 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 3. INSTALL INJECTION PUMP INSULATOR |
Install the injection pump insulator.

Text in Illustration 

Front Side of Vehicle
- NOTICE:
- When installing the injection pump insulator, be sure to hold down the part labeled A in the illustration.
- Make sure that the shape of the injection pump insulator fits correctly with the timing gear case assembly, cylinder block sub-assembly and oil cooler cover.
- When installing the injection pump insulator, be sure to hold down the part labeled A in the illustration.
| 4. INSTALL NO. 2 FUEL PIPE |
Apply a light coat of fuel to the O-ring of the fuel check valve.

Text in Illustration *1
O-Ring
Temporarily install the No. 2 fuel pipe and a new gasket with the union bolt.

Text in Illustration *1
Gasket


Union Bolt


Fuel Check Valve


Fuel Tube Connector


Bolt
Temporarily install a new gasket and the fuel check valve.
Temporarily install the bolt.
Using a 6 mm hexagon wrench, tighten the union bolt.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
- NOTICE:
- Make sure the gasket of union bolt A contacts the No. 2 fuel pipe as shown in the illustration when tightening the union bolt.
Tighten the fuel check valve.
- Torque:
- 32 N*m{ 321 kgf*cm , 23 ft.*lbf }
Tighten the bolt.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Connect the fuel tube connector (Click here).
| 5. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
- NOTICE:
- When replacing an injector assembly, it is necessary to replace the 4 injection pipe sub-assemblies with new ones.
- Keep the joints of the injection pipe sub-assembly clean.
- When replacing an injector assembly, it is necessary to replace the 4 injection pipe sub-assemblies with new ones.
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Using a 17 mm union nut wrench, tighten the No. 4 injection pipe sub-assembly union nut on the common rail assembly side.

- Torque:
- Specified tightening torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
Text in Illustration *a
Torque Wrench Fulcrum Length
- HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 32 N*m (324 kgf*cm, 23 ft.*lbf)
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
Using a 17 mm union nut wrench, tighten the injection pipe sub-assembly union nuts on the injector assembly side.

- Torque:
- Specified tightening torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
Text in Illustration *a
Torque Wrench Fulcrum Length
- HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 32 N*m (324 kgf*cm, 23 ft.*lbf)
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
| 6. INSTALL INTAKE AIR CONNECTOR |
Set a new gasket on the intake manifold.

Text in Illustration *1
Claw
- NOTICE:
- Make sure the claw of the gasket faces the intake manifold as shown in the illustration.
Install the intake air connector with the 3 bolts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
| 7. INSTALL GAS FILTER BRACKET |
Install the gas filter bracket with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Attach the clamp and connect the wire harness.
| 8. INSTALL NO. 1 GAS FILTER |
Install the No. 1gas filter to the gas filter bracket.
Connect the vacuum hose.
| 9. INSTALL THROTTLE BODY BRACKET |
Temporarily install the throttle body bracket with the 3 bolts.

Tighten the 3 bolts of the throttle body bracket in the order shown in the illustration.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
| 10. INSTALL EMISSION CONTROL VALVE BRACKET |
Install the emission control valve bracket with the bolt.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 11. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR |
Install the manifold absolute pressure sensor with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the vacuum hose and manifold absolute pressure sensor connector.
| 12. CONNECT WIRE HARNESS |
Attach the 5 clamps and connect the wire harness to the cowl top panel.
for LHD:
Connect the wire harness with the bolt.- Torque:
- 22 N*m{ 219 kgf*cm , 16 ft.*lbf }
Connect the wire harness with the bolt.
- Torque:
- 13 N*m{ 131 kgf*cm , 9 ft.*lbf }
| 13. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY |
| 14. INSTALL TIMING BELT |
| 15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 17. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the reservoir tank.
- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
w/ Rear Heater
14.9 liters (15.7 US qts, 13.1 Imp. qts)
w/o Rear Heater
13.1 liters (13.8 US qts, 11.5 Imp. qts)
for Manual Transmission
w/ Rear Heater
15.0 liters (15.8 US qts, 13.2 Imp. qts)
w/o Rear Heater
13.2 liters (13.9 US qts, 11.6 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Please contact your TOYOTA dealer for further details.
- for Cold Area Specification Vehicles:
Please contact any authorized TOYOTA dealer or repairer or another duly qualified and equipped professional for further details.
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down to ambient temperature.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the FULL line, add TOYOTA SLLC to the FULL line.
| 18. BLEED AIR FROM FUEL SYSTEM |
Using the hand pump mounted on the fuel filter cap, bleed air from the fuel system. Continue pumping until the pump resistance increases.

- NOTICE:
- The maximum hand pump pumping speed is 2 strokes per second.
- The hand pump must be pushed with a full stroke during pumping.
- When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
- If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
- If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
- If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.
- The maximum hand pump pumping speed is 2 strokes per second.
Check if the engine starts.
- NOTICE:
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
- Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
- Use a fully-charged battery.
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

Text in Illustration *a
Reference
(Active Test Operation)
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.


- HINT:
- When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
- HINT:
- It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
- OK:
- No DTCs are output.
| 19. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
| 20. INSPECT FOR COOLANT LEAK |
- NOTICE:
- Before each inspection, turn the A/C switch off.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 21. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
Intelligent Tester Display
Test Part
Control Range
Diagnostic Note
Test the Fuel Leak
Pressurize common rail interior and check for fuel leaks
Stop/Start
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
- The above conditions are maintained while the Active Test is being performed.
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
