2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE REAR SEAT UPPER RECLINING COVER LH

B237615E01
  1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B237616
  1. Remove the 3 screws and reclining adjuster release handle LH.


3. REMOVE CENTER SEAT HINGE COVER LH

B237617
  1. Using a clip remover, remove the clip.

  1. Detach the 2 guides and remove the center seat hinge cover LH.


4. REMOVE REAR SEAT CUSHION MOULDING LH

B237619
  1. Using a clip remover, detach the clip.

  1. Using a moulding remover, detach the 3 claws.

  1. Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.


5. REMOVE REAR SEATBACK LOCK STRIKER COVER LH

B237621
  1. Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.


6. REMOVE SEAT CUSHION COVER WITH PAD

  1. B359313
    w/ Seat Heater System:

    1. Disconnect the 2 rear seat heater connectors.

    2. B360133
      Pull out the wire harness as shown in the illustration.

  1. B237622
    Detach the hooks.

  1. B237624
    Detach the hook and remove the seat cushion cover with pad.


7. REMOVE REAR NO. 2 SEAT PROTECTOR

B237626
  1. Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.


8. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER

B237627
  1. Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.


9. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

B248327E01
  1. Cut off the 23 tack pins and remove the rear seat cushion heater assembly from the separate type rear seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin


10. REMOVE REAR SEAT CUSHION EDGE PROTECTOR
  1. Remove the rear seat cushion edge protector from the cushion spring.


11. REMOVE CENTER SEATBACK ASSEMBLY

B237629
  1. Remove the 2 bolts and center seatback assembly.


12. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY
  1. Remove the rear seat center headrest assembly.


13. REMOVE CENTER SEAT HINGE COVER

B237630
  1. Using a clip remover, remove the clip.

  1. Detach the 2 guides and remove the center seat hinge cover.


14. REMOVE REAR SEAT RECLINING BRACKET LH

B237632
  1. Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket LH.


15. REMOVE REAR SEAT RECLINING BRACKET RH
  1. Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket RH.


16. REMOVE REAR SEATBACK STAY COVER LH

B237633
  1. Using a moulding remover, detach the 3 claws.

  1. Detach the guide and remove the rear seatback stay cover LH.


17. REMOVE REAR SEATBACK STAY COVER RH
  1. Using a moulding remover, detach the 3 claws.

  1. Detach the guide and remove the rear seatback stay cover RH.


18. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY

  1. B237634
    Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes.

  1. B237635
    Remove the nut and rear center seat armrest support LH.

  1. B237636
    Remove the rear seat center armrest assembly as shown in the illustration.


19. REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

  1. B237638
    Remove the 2 screws.

  1. B237639
    Using moulding remover A, detach the 2 claws and remove the rear seat center armrest cup holder sub-assembly.


20. REMOVE REAR SEATBACK COVER

B237641
  1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

    HINT:
    Tape the screwdriver tip before use.


21. REMOVE REAR SEATBACK LOCK COVER

B237642
  1. Using a moulding remover, detach the claw.

  1. Move the cover in the direction of the arrow to detach the clip and 2 guides, and then remove the rear seatback lock cover.


22. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

B237644
  1. Using a clip remover, detach the 5 clips and remove the rear seatback board sub-assembly.


23. REMOVE SEAT ARMREST COVER

  1. B237645
    Detach the hooks.

  1. B237647
    Remove the seat armrest cover with pad.

  1. B237650
    Remove the seat armrest cover from the pad.


24. REMOVE REAR SEAT HEADREST SUPPORT

B237651
  1. Detach the 4 claws and remove the 2 rear seat headrest supports.


25. REMOVE NO. 1 SEATBACK COVER

  1. B237652
    Using moulding remover A, detach the 2 claws.

  1. B237654
    Detach the guide and remove the No. 1 seatback cover.


26. REMOVE REAR SEAT LOCK ASSEMBLY LH

B237656
  1. Detach the clamp and disconnect the wire.

  1. Remove the 2 bolts and rear seat lock assembly LH.


27. REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER

B237657
  1. Remove the rear No. 1 seat lock control lever as shown in the illustration.


28. REMOVE FOLD SEATBACK WIRE

B237659
  1. Detach the 2 claws and remove the fold seatback wire.


29. REMOVE COAT HOOK CAP

B237660E01
  1. Using a screwdriver, detach the 2 claws and guide, and then remove the coat hook cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


30. REMOVE CENTER NO. 2 SEATBACK COVER

B237662
  1. Remove the 3 screws and center No. 2 seatback cover.


31. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B237670
  1. Remove the bolt and rear No. 1 seat inner belt assembly LH and disconnect the No. 1 seat 3 point type belt assembly LH.


32. REMOVE RECLINING ADJUSTER KNOB CAP LH

B237663E01
  1. Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


33. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B237665
    Remove the 2 screws.

  1. B165025E02
    Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.


34. REMOVE SEAT BELT ANCHOR COVER CAP

  1. B237666E01
    Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


35. REMOVE REAR SEAT SHOULDER BELT COVER
  1. Disconnect the outer belt from the rear seat shoulder belt cover.

  1. B360121
    Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.


36. REMOVE REAR SEATBACK COVER

B237641
  1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

    HINT:
    Tape the screwdriver tip before use.


37. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH

B237671
  1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.


38. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B237672
  1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.


39. REMOVE SEATBACK COVER WITH PAD

  1. B237673E01
    Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.
    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring

  1. B237676
    Disconnect the outer belt from the seatback cover with pad.

  1. w/ Seat Heater System:

    1. B360132
      Remove the wire harness.


40. REMOVE SEPARATE TYPE REAR SEATBACK COVER

  1. B248335
    w/ Seat Heater System:

    1. Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.

  1. B237677
    Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.


41. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

B248650E01
  1. Cut off the 11 tack pins which fasten the rear seatback heater assembly to the separate type rear seatback cover, and then remove the rear seatback heater assembly from the separate type rear seatback cover.

    Text in Illustration 
    *1
    Tack Pin


42. REMOVE REAR SEATBACK EDGE PROTECTOR
  1. Remove the rear seatback edge protector from the rear seatback frame sub-assembly LH.


43. REMOVE REAR SEAT INNER RECLINING COVER LH

B237679
  1. Remove the 2 screws.

  1. Detach the guide and remove the rear seat inner reclining cover LH.


44. REMOVE RECLINING ADJUSTER INSIDE COVER LH

B237680
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the reclining adjuster inside cover LH.


45. REMOVE REAR SEAT REAR CUSHION MOULDING LH

B237681
  1. Using a clip remover, detach the clip.

  1. Using moulding remover A, detach the 4 claws.

  1. Move the rear seat rear cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat rear cushion moulding LH.


46. REMOVE CAP

B237683
  1. Detach the 2 claws and remove the cap.


47. REMOVE REAR SEAT RECLINING COVER INNER LH

B237684
  1. Detach the claw and guide, and then remove the rear seat reclining cover inner LH.


48. REMOVE REAR SEAT CUSHION SPRING DAMPER

B237686
  1. Remove the 2 nuts and rear seat cushion spring damper.


49. REMOVE REAR SEAT SHOULDER BELT GUIDE

B237687
  1. Detach the claw and guide, and then remove the rear seat shoulder belt guide.


50. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B241742
  1. Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.


51. REMOVE REAR SEAT RECLINING CONTROL CABLE

  1. Cut off the 4 cable ties.

    B237688

  1. Detach the 3 cable clamps and disconnect the cable, and then remove the rear seat reclining control cable.

    B237689


52. REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE

  1. Detach the 3 cable clamps and disconnect the cable, and then remove the rear No. 2 seat reclining control cable.

    B237690


53. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH

B237691
  1. Remove the 2 nuts and rear back lock control lever sub-assembly LH.


54. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

  1. B248344
    Disconnect the connector.

  1. Detach the 2 clamps and remove the seat heater control sub-assembly.


55. REMOVE REAR SEAT WIRE LH (w/ Seat Heater System)

  1. B291034
    Detach the claw and disconnect the rear seat wire connector.

  1. Detach the clamp and remove the rear seat wire LH.


56. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH

B237692
  1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.

  1. Remove the 2 bolts and rear seatback frame sub-assembly LH.


57. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

B237694
  1. Remove the 6 nuts and rear seat cushion frame sub-assembly LH.


58. REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH

B237695
  1. Slide the slide rail to the rearmost position.

  1. Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle LH.

    HINT:
    Insert the screwdriver into the hole shown in the illustration while looking into the hole.

← REMOVAL (from Aug 2013)REASSEMBLY (from Aug 2013) →