REMOVAL
Removal / installation · Vehicles built from Aug 2013
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for RHD and LHD vehicles.
| 1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
Remove the rear No. 1 seat assembly LH (Click here).
| 2. REMOVE REAR SEAT UPPER RECLINING COVER LH |
![]() ![]() |
Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() ![]() |
Remove the 3 screws and reclining adjuster release handle LH.
| 4. REMOVE CENTER SEAT HINGE COVER RH |
![]() ![]() |
Using a clip remover, remove the clip.
Detach the 2 guides and remove the center seat hinge cover LH.
| 5. REMOVE REAR SEAT CUSHION MOULDING LH |
![]() ![]() |
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.
| 6. REMOVE REAR SEATBACK LOCK STRIKER COVER LH |
![]() ![]() |
Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.
| 7. REMOVE SEAT CUSHION COVER WITH PAD |
w/ Seat Heater System:

Disconnect the 2 rear seat heater connectors.
Pull out the wire harness as shown in the illustration.

Detach the hooks.

Detach the hook and remove the seat cushion cover with pad.

| 8. REMOVE CENTER SEATBACK ASSEMBLY |
![]() ![]() |
Remove the 2 bolts and center seatback assembly.
| 9. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Remove the bolt and inner belt, and disconnect the 3 point type belt anchor.

| 10. REMOVE RECLINING ADJUSTER KNOB CAP LH |
![]() ![]() |
Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 11. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
Remove the 2 screws.

Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.

| 12. REMOVE SEAT BELT ANCHOR COVER CAP |
Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 13. REMOVE REAR SEAT SHOULDER BELT COVER |
Disconnect the outer belt from the rear seat shoulder belt cover.
Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.

| 14. REMOVE REAR SEATBACK COVER |
![]() ![]() |
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
- HINT:
- Tape the screwdriver tip before use.
| 15. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH |
![]() ![]() |
Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.
| 16. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() ![]() |
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
| 17. REMOVE SEATBACK COVER WITH PAD |
Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.

Text in Illustration *1
Hook
*2
Hog Ring
Disconnect the outer belt from the seatback cover with pad.

w/ Seat Heater System:
Remove the wire harness.

| 18. REMOVE REAR SEAT SHOULDER BELT GUIDE |
![]() ![]() |
Detach the claw and guide, and then remove the rear seat shoulder belt guide.
| 19. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
![]() ![]() |
Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.












