2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B241742E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the nut and bolt as shown in the illustration.

    HINT:
    First install the bolt, and then install the nut.

    Torque:
    for bolt:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for nut:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Nut


2. INSTALL REAR SEAT SHOULDER BELT GUIDE
  1. Attach the guide and claw to install the rear seat shoulder belt guide.


3. INSTALL SEATBACK COVER WITH PAD

  1. w/ Seat Heater System:

    1. B360132E01
      Install the wire harness as shown in the illustration.
      Text in Illustration 
      *a
      Paint Mark

  1. B237675
    Connect the outer belt to the seatback cover with pad.

  1. B237674E01
    Attach the hooks.
    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hook
    *3
    Hog Ring

  1. Using hog ring pliers, install the seatback cover with pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type rear seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.


4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


5. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
  1. Attach the 7 clips to install the rear seatback board carpet assembly LH.


6. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the rear seatback cover.


7. INSTALL REAR SEAT SHOULDER BELT COVER
  1. Connect the outer belt to the rear seat shoulder belt cover.

  1. B237669
    Attach the 2 guides and 2 claws to install the rear seat shoulder belt cover.


8. INSTALL SEAT BELT ANCHOR COVER CAP

B237667
  1. Attach the 2 claws to install the seat belt anchor cover cap.


9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

B237667
  1. Attach the 2 claws to install the seat belt anchor cover cap.


10. INSTALL RECLINING ADJUSTER KNOB CAP LH

B237664
  1. Attach the guide and claw to install the reclining adjuster knob cap LH.


11. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B242874E01
  1. Install the inner belt and connect the 3 point type belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the seatback frame.

    Text in Illustration 
    *a
    Protruding Part


12. INSTALL CENTER SEATBACK ASSEMBLY
  1. Install the center seatback assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


13. INSTALL SEAT CUSHION COVER WITH PAD

  1. B237625
    Attach the hook.

  1. B237623
    Attach the hooks to install the seat cushion cover with pad.

  1. w/ Seat Heater System:

    1. B360133
      Pass the wire harness as shown in the illustration.

    2. B359313
      Connect the 2 rear seat heater connectors.


14. INSTALL REAR SEATBACK LOCK STRIKER COVER LH
  1. Attach the 3 clips to install the rear seatback lock striker cover LH.


15. INSTALL REAR SEAT CUSHION MOULDING LH

B237620
  1. Move the rear seat cushion moulding LH in the direction of the arrow to attach the guide.

  1. Attach the 3 claws and clip to install the rear seat cushion moulding LH.


16. INSTALL CENTER SEAT HINGE COVER RH

B237618
  1. Attach the 2 guides and install the center seat hinge cover LH with the clip.


17. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Install the reclining adjuster release handle LH with the 3 screws.


18. INSTALL REAR SEAT UPPER RECLINING COVER LH

B237786
  1. Attach the 3 claws to install the rear seat upper reclining cover LH.


19. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Install the rear No. 1 seat assembly LH (Click here).

← INSPECTION (from Aug 2013)COMPONENTS (from Aug 2013) →