DISASSEMBLY
Removal / installation · Vehicles built from Aug 2013
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
| 1. REMOVE REAR SEAT RECLINING COVER LH |
![]() ![]() |
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide and remove the cover.
| 2. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
![]() ![]() |
Remove the 2 screws.
Using a moulding remover, detach the 2 claws.
Move the cover in the direction of the arrow to detach the guide.
Detach the 2 hooks and remove the cover.

| 3. REMOVE REAR NO. 2 SEAT CUSHION |
![]() ![]() |
Remove the screw and cushion.
| 4. REMOVE REAR RECLINING ADJUSTER INSIDE COVER LH |
![]() ![]() |
Remove the 2 screws.
Detach the 2 claws and remove the cover.
| 5. REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY |
![]() ![]() |
Using a screwdriver, remove the stopper.
Remove the pin as shown in the illustration.
- HINT:
- Use the same procedure for both pins.
| 6. REMOVE REAR SEAT HINGE PAWL GUIDE |
![]() ![]() |
Detach the 4 claws and remove the pawl guide.
- HINT:
- Use the same procedure for both pawl guides.
| 7. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH |
Using a screwdriver, remove the E-ring.

Remove the pin.

Using a screwdriver, detach the 10 claws.

- HINT:
- Tape the screwdriver tip before use.
Remove the 5 screws.

Disconnect the reclining release handle from the under cover.
Raise the under cover.
Using a screwdriver, remove the spring of the seat stay ball-joint.

Disconnect the seat stay from the seat cushion frame.
Remove the seat hinge and seat stay as a unit.
- NOTICE:
- The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.
- HINT:
- If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.
| 8. REMOVE REAR SEAT STAY SUB-ASSEMBLY |
- HINT:
- As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
- If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.
- As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
| 9. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH |
Using a screwdriver, remove the E-ring.

Remove the pin and hinge.

| 10. REMOVE REAR SEAT CUSHION EDGE PROTECTOR |
![]() ![]() |
Remove the protector from the cushion frame.
- HINT:
- Use the same procedure for both protectors.
| 11. REMOVE FOLD SEAT LEG LOCK CUSHION |
![]() ![]() |
Remove the cushion from the protector.
- HINT:
- Use the same procedure for both cushions.
| 12. REMOVE REAR SEAT CUSHION SUPPORT SPRING |
![]() ![]() |
Remove the spring from the seat cushion frame.
- HINT:
- Use the same procedure for both springs.
| 13. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH |
Remove the under cover.
| 14. REMOVE REAR NO. 2 SEAT HINGE COVER LH |
![]() ![]() |
Detach the 3 claws and remove the cover.
| 15. REMOVE REAR NO. 2 SEAT HINGE COVER RH |
Detach the 3 claws and remove the cover.
| 16. REMOVE REAR SEAT INNER BELT ASSEMBLY |
![]() ![]() |
Remove the bolt and inner belt.
| 17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH |
Remove the bolt and disconnect the inner belt.

| 18. REMOVE SEAT CUSHION COVER WITH PAD |
Cut off the tack pins and remove the carpet from the cushion pad.

Text in Illustration *1
Tack Pin
Remove the hog rings and seat cushion cover with pad.

| 19. REMOVE REAR SEAT INNER CUSHION EDGE PROTECTOR LH |
Cut off the tack pins and remove the carpet from the cushion pad.

Text in Illustration *1
Tack Pin
| 20. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER |
Remove the hog rings and seat cushion cover from the seat cushion pad.

| 21. REMOVE REAR SEATBACK COVER |
![]() ![]() |
Using a screwdriver, detach the 8 claws and remove the 2 covers.
- HINT:
- Tape the screwdriver tip before use.
| 22. REMOVE NO. 1 SEATBACK PAD LH |
Remove the bolt and disconnect the outer belt.

Detach the fastening tape and open the cover.

Text in Illustration *1
Fastening Tape
Remove the 6 hog rings.

Open the 2 fasteners, and then open the seatback cover.

Remove the seatback pad.

| 23. REMOVE REAR SEAT INNER RECLINING COVER RH |
![]() ![]() |
Remove the screw.
Detach the guide and remove the cover.
| 24. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY |
![]() ![]() |
Remove the 2 bolts, center armrest and bush.
| 25. REMOVE REAR SEAT CENTER ARMREST HINGE |
![]() ![]() |
Remove the screw and armrest hinge.
| 26. REMOVE REAR SEAT ARMREST SUPPORT |
![]() ![]() |
Remove the armrest support.
| 27. REMOVE SHOULDER BELT ANCHOR COVER |
![]() ![]() |
Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 28. REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH |
Detach the 4 claws and remove the cover.

Disconnect the outer belt.

| 29. REMOVE REAR SEATBACK LOCK STRIKER COVER |
![]() ![]() |
Using a screwdriver, detach the claw and guide, and then remove the cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 30. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
Remove the 2 screws.

Disconnect the cable in the order shown in the illustration and remove the lever.

| 31. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() ![]() |
Detach the 8 claws and remove the 4 supports.
| 32. REMOVE SEATBACK COVER WITH PAD |
Detach the 2 hooks and remove the seatback cover with pad.

Disconnect the outer belt from the seatback cover with pad.

| 33. REMOVE SEPARATE TYPE REAR SEATBACK COVER |
Remove the hog rings and detach the fastening tape, and then remove the seatback cover from the seatback pad.


Text in Illustration *1
Fastening Tape
-
-
| 34. REMOVE REAR NO. 1 SEAT RECLINING COVER LH |
![]() ![]() |
Detach the 2 claws and remove the cover.
| 35. REMOVE RECLINING ADJUSTER COVER LH |
![]() ![]() |
Remove the 4 screws.
Detach the 4 claws and remove the cover.
| 36. REMOVE REAR SEAT SHOULDER BELT GUIDE |
Detach the 2 claws and open the cover.

Disconnect the seat belt from the belt guide.

Detach the 4 guides and remove the belt guide.

| 37. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
Remove the 3 nuts and belt sensor.

Remove the nut and seat belt.

| 38. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
![]() ![]() |
Detach the 2 cable clamps, and then disconnect the cable and remove it.
| 39. REMOVE REAR SEAT INNER RECLINING COVER LH |
![]() ![]() |
Detach the 2 claws and 2 guides, and then remove the cover.
| 40. REMOVE REAR SEAT RECLINING COVER INNER LH |
![]() ![]() |
Detach the 2 guides and remove the cover.
| 41. REMOVE REAR SEAT RECLINING COVER INNER RH |
![]() ![]() |
Detach the 2 guides and remove the cover.
| 42. REMOVE SEATBACK STOPPER PLATE |
![]() ![]() |
Remove the 3 bolts and plate.
| 43. REMOVE REAR CENTER SEAT ARMREST BUSH |
![]() ![]() |
Detach the 3 claws and remove the bush.
| 44. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH |
![]() ![]() |
Remove the 4 bolts, bracket and seatback frame.
| 45. REMOVE REAR SEATBACK INNER ADJUSTER ASSEMBLY LH |
![]() ![]() |
Remove the 2 bolts, adjuster and cover.
| 46. REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY |
![]() ![]() |
Remove the bolt and bracket.
| 47. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH |
Cut off the 2 cable ties.

Detach the 3 cable clamps, and then disconnect the cable and remove it.































