2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH
  1. Install the cable to the seat cushion frame.

  1. Attach the 3 cable clamps and connect the cable.

  1. Install 2 new cable ties.


2. INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY
  1. Install the bracket with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


3. INSTALL REAR SEATBACK INNER ADJUSTER ASSEMBLY LH

B241172E01
  1. Install the cover and adjuster with the 2 bolts.

    Torque:
    Bolt A:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }
    Bolt B:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B


4. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH
  1. Install the seatback frame and bracket with the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


5. INSTALL REAR CENTER SEAT ARMREST BUSH
  1. Attach the 3 claws to install the bush.


6. INSTALL SEATBACK STOPPER PLATE
  1. Install the plate with 3 bolts.


7. INSTALL REAR SEAT RECLINING COVER INNER RH
  1. Attach the 2 guides to install the cover.


8. INSTALL REAR SEAT RECLINING COVER INNER LH
  1. Attach the 2 guides to install the cover.


9. INSTALL REAR SEAT INNER RECLINING COVER LH
  1. Attach the 2 guides and 2 claws to install the cover.


10. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
  1. Install the cable to the seatback frame.

  1. Attach the 2 cable clamps and connect the cable.


11. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B244722E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the seat belt positioning holes with the claws and install the retractor of the 3 point type belt with the nut as shown in the illustration.

  1. Install the belt sensor with the 3 nuts.


12. INSTALL REAR SEAT SHOULDER BELT GUIDE
  1. Attach the 4 guides to install the belt guide.

  1. B241167
    Connect the outer belt to the belt guide.

  1. Attach the 2 claws to close the cover.


13. INSTALL RECLINING ADJUSTER COVER LH

B241135
  1. Attach the 4 claws to install the cover.

  1. Install the 4 screws.


14. INSTALL REAR NO. 1 SEAT RECLINING COVER LH
  1. Attach the 2 claws to install the cover.


15. INSTALL SEPARATE TYPE REAR SEATBACK COVER
  1. Install the seatback cover with 2 new hog rings and attach the fastening tape.

  1. Using hog ring pliers, install the new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.
    B241131E01

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Fastening Tape


16. INSTALL SEATBACK COVER WITH PAD

  1. B241128
    Connect the outer belt to the seatback cover with pad.

  1. Attach the 2 hooks to install the seatback cover with pad.


17. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 8 claws to install the 4 supports.


18. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B165026E02
    Connect the cable in the order shown in the illustration to install the lever.

  1. Install the 2 screws.


19. INSTALL REAR SEATBACK LOCK STRIKER COVER

B237664
  1. Attach the guide and claw to install the cover.


20. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

  1. B241126
    Connect the outer belt to the cover.

  1. B241124
    Attach the 4 claws to install the cover.


21. INSTALL SHOULDER BELT ANCHOR COVER

B241123
  1. Attach the 2 claws and 2 guides to install the cover.


22. INSTALL REAR SEAT ARMREST SUPPORT
  1. Install the armrest support to the armrest hinge.


23. INSTALL REAR SEAT CENTER ARMREST HINGE
  1. Install the armrest hinge with the screw.


24. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
  1. Install the center armrest and bush with the 2 bolts.


25. INSTALL REAR SEAT INNER RECLINING COVER RH

B241118
  1. Attach the guide to install the cover.

  1. Install the screw.


26. INSTALL NO. 1 SEATBACK PAD LH
  1. Install the seatback pad.

  1. B241115
    Close the 2 fasteners, and then close the seatback cover.

  1. B242243E01
    Using hog ring pliers, install 6 new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Attach the 3 fastening tapes and close the cover.

  1. B241112E01
    Connect the outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.

    Text in Illustration 
    *1
    Protruding Part


27. INSTALL REAR SEATBACK COVER
  1. Attach the 8 claws to install the 2 covers.


28. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

B241110E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


29. INSTALL REAR SEAT INNER CUSHION EDGE PROTECTOR LH
  1. Install the protector with new tack pins.


30. INSTALL SEAT CUSHION COVER WITH PAD

B241108E01
  1. Using hog ring pliers, install the seatback cover with pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Install the carpet with new tack pins.


31. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

B242890E01
  1. Connect the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.

    Text in Illustration 
    *a
    Protruding Part


32. INSTALL REAR SEAT INNER BELT ASSEMBLY

B244719E01
  1. Install the inner belt with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the rear seat adjuster.

    Text in Illustration 
    *a
    Protruding Part


33. INSTALL REAR NO. 2 SEAT HINGE COVER RH
  1. Attach the 3 claws to install the cover.


34. INSTALL REAR NO. 2 SEAT HINGE COVER LH
  1. Attach the 3 claws to install the cover.


35. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
  1. Temporarily install the under cover to the seat cushion frame.


36. INSTALL REAR SEAT CUSHION SUPPORT SPRING
  1. Install the spring to the seat cushion frame

    HINT:
    Use the same procedure for both springs.


37. INSTALL FOLD SEAT LEG LOCK CUSHION

B241087
  1. Install the cushion to the protector.

    HINT:
    Use the same procedure for both cushions.


38. INSTALL REAR SEAT CUSHION EDGE PROTECTOR
  1. Install the protector to the cushion frame.

    HINT:
    Use the same procedure for both protectors.


39. INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH
  1. Install the hinge.

  1. Install the pin to the hinge.

  1. Install a new E-ring.


40. INSTALL REAR SEAT STAY SUB-ASSEMBLY
  1. Connect the seat stay ball-joint to the seat hinge.

    HINT:
    It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.


41. INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
  1. Install the spring of the seat stay ball-joint.

  1. Temporarily install the seat hinge and seat stay as a unit.

  1. Raise the under cover.

  1. B241091
    Connect the seat stay to the seat cushion frame.

  1. B241177
    Connect the reclining release handle to the under cover.

  1. Install the 5 screws.

  1. Attach the 10 claws to install the under cover.

  1. Install the pin to the hinge.

  1. Install a new E-ring.


42. INSTALL REAR SEAT HINGE PAWL GUIDE
  1. Attach the 4 claws to install the pawl guide.

    HINT:
    Use the same procedure for both pawl guides.


43. INSTALL SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY

B241081
  1. Install the pin as shown in the illustration.

  1. Install the stopper.

    HINT:
    Use the same procedure for both pins.


44. INSTALL REAR RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.


45. INSTALL REAR NO. 2 SEAT CUSHION
  1. Install the cushion with the screw.


46. INSTALL REAR NO. 1 SEAT RECLINING COVER RH
  1. Attach the 2 hooks.

  1. B241101
    Attach the guide and 2 claws to install the cover.

  1. Install the 2 screws.


47. INSTALL REAR SEAT RECLINING COVER LH

  1. B241079
    Attach the guide and 2 claws to install the cover.

  1. Install the 2 screws.

← DISASSEMBLY (from Aug 2013)INSTALLATION (from Aug 2013) →