2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. Remove the rear No. 1 seat assembly LH (Click here).


2. REMOVE REAR SEAT RECLINING COVER LH

B241078
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the guide and remove the cover.


3. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B241100
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the guide.

  1. B241102
    Detach the 2 hooks and remove the cover.


4. REMOVE REAR NO. 2 SEAT CUSHION

B241103
  1. Remove the screw and cushion.


5. REMOVE REAR RECLINING ADJUSTER INSIDE COVER LH

B241104
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the cover.


6. REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY

B241080
  1. Using a screwdriver, remove the stopper.

  1. Remove the pin as shown in the illustration.

    HINT:
    Use the same procedure for both pins.


7. REMOVE REAR SEAT HINGE PAWL GUIDE

B241082
  1. Detach the 4 claws and remove the pawl guide.

    HINT:
    Use the same procedure for both pawl guides.


8. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH

  1. B241088
    Using a screwdriver, remove the E-ring.

  1. B241089
    Remove the pin.

  1. B241105
    Using a screwdriver, detach the 10 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B241106
    Remove the 5 screws.

  1. Disconnect the reclining release handle from the under cover.

  1. Raise the under cover.

  1. B241090
    Using a screwdriver, remove the spring of the seat stay ball-joint.

  1. Disconnect the seat stay from the seat cushion frame.

  1. Remove the seat hinge and seat stay as a unit.

    NOTICE:
    The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.

    HINT:
    If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.


9. REMOVE REAR SEAT STAY SUB-ASSEMBLY

HINT:
  1. As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
  2. If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.


10. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH

  1. B241083
    Using a screwdriver, remove the E-ring.

  1. B241084
    Remove the pin and hinge.


11. REMOVE REAR SEAT CUSHION EDGE PROTECTOR

B241085
  1. Remove the protector from the cushion frame.

    HINT:
    Use the same procedure for both protectors.


12. REMOVE FOLD SEAT LEG LOCK CUSHION

B241086
  1. Remove the cushion from the protector.

    HINT:
    Use the same procedure for both cushions.


13. REMOVE REAR SEAT CUSHION SUPPORT SPRING

B242241
  1. Remove the spring from the seat cushion frame.

    HINT:
    Use the same procedure for both springs.


14. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
  1. Remove the under cover.


15. REMOVE REAR NO. 2 SEAT HINGE COVER LH

B241049
  1. Detach the 3 claws and remove the cover.


16. REMOVE REAR NO. 2 SEAT HINGE COVER RH
  1. Detach the 3 claws and remove the cover.


17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

  1. B242889
    Remove the bolt and disconnect the inner belt.

← COMPONENTS (from Aug 2013)INSTALLATION (from Aug 2013) →